Gargoyle CLI

Report problems and success stories with Gargoyle on various hardware platforms.

Moderator: Moderators

GhostYou
Posts: 3
Joined: Sat Sep 03, 2016 3:54 am

Re: Gargoyle CLI

Post by GhostYou »

Thank You so much for the wan port tip. sorry it not so long but that got me in and all works fine now :)

jocogi
Posts: 5
Joined: Thu Jun 15, 2017 12:45 pm

Re: Gargoyle CLI

Post by jocogi »

Hey guys, I've successfully used this guide before to reset gargoyle to its default through Putty. I forget what ip I used for it last time, and now I cannot get Putty to connect when I've come back to it months later. I had it set to bridge mode. It's a WNDR3800 trying to connect through the WAN port... Any suggestions? This time I used the ip settings in the video above, but from memory I had to use something different.

Thanks in advance for your help!

Lantis
Moderator
Posts: 6721
Joined: Mon Jan 05, 2015 5:33 am
Location: Australia

Re: Gargoyle CLI

Post by Lantis »

I think you should use the LAN port on that device
Addresses in the 192.168.1.x range will be ok.
Remember to use telnet for 1.9.1 and below, and SSH for 1.10.0
http://lantisproject.com/downloads/gargoyle_ispyisail.php for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.

jocogi
Posts: 5
Joined: Thu Jun 15, 2017 12:45 pm

Re: Gargoyle CLI

Post by jocogi »

Ok that worked to get in. Thank you for your help. Now I can't seem to get the firstboot command to do anything. I swear it worked fine last time.

Also I'm happy to just do a reflash to 1.10.0 if that's simpler. Is netcat the best way to do this? Can I do it over telnet?

Lantis
Moderator
Posts: 6721
Joined: Mon Jan 05, 2015 5:33 am
Location: Australia

Re: Gargoyle CLI

Post by Lantis »

“firstboot -y” is the new command.

I’ve never flashed over firstboot sorry. I’m sure I’ll have to one day, but for now I can’t offer any advice.
http://lantisproject.com/downloads/gargoyle_ispyisail.php for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.

jocogi
Posts: 5
Joined: Thu Jun 15, 2017 12:45 pm

Re: Gargoyle CLI

Post by jocogi »

firstboot -y just sends me to a new line the same as the other command. I am still on 1.9.2. I swear it worked fine months ago. I'm not sure what I am doing differently now.

Regarding flashing, what is the recommended way without having access to the web gui?

Thank you again for your ongoing help with

Lantis
Moderator
Posts: 6721
Joined: Mon Jan 05, 2015 5:33 am
Location: Australia

Re: Gargoyle CLI

Post by Lantis »

Then you type “reboot” and try to connect to the router normally
http://lantisproject.com/downloads/gargoyle_ispyisail.php for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.

peterpux
Posts: 21
Joined: Thu Feb 04, 2016 2:18 pm

Re: Gargoyle CLI

Post by peterpux »

What is the command in terminal (Linux) to log into gargoyle in failsafe?
I’ve only used putty and winSCP but have not learned how to do it myself in CLI

I will use a raspberry pi 4 to correct my config using failsafe and terminal
From Nunavik, Quebec, Canada
WNDR 3800 with Gargoyle 1.10.x Dec 18
WNDR 3800 Repeater with Gargoyle 1.10.x

RomanHK
Posts: 794
Joined: Sat May 04, 2013 4:18 pm
Location: Czech Republik

Re: Gargoyle CLI

Post by RomanHK »

https://openwrt.org/docs/guide-user/tro ... tory_reset

Video tutorial: https://www.youtube.com/watch?v=_NqHpRHl8gQ

Access to Failsafe Gargoyle < v1.10:
Use eg PuTTY, protocol: Telnet, IP address: 192.168.1.1, Port: 23, User: root, Password: no password

Access to Failsafe Gargoyle >= v1.10:
Use eg PuTTY, protocol: SSH, IP address: 192.168.1.1, Port: 22, User: root, Password: no password

EDIT: You will not find a log extract in this mode (you can only watch the boot log via a serial cable) - this is a rescue mode.
Turris Omnia with OpenWrt 21.02 - Tested
Linksys WRT3200ACM with Gargoyle 1.13.x
TL-WR1043ND v2 with Gargoyle 1.10.0

http://gargoyle.romanhk.cz custom builds by gargoyle users

Post Reply