Page 4 of 30
Re: Successfully flashed a router? Tell Us!
Posted: Mon Nov 21, 2011 5:41 pm
by John_M
I just checked last night...my Buffalo WZR-HP-G300NH has been up and running Gargoyle 1.4.3 for 76 days. No reboots. No dropouts. The only reason it is 76 days is that I had to reboot when I shut the system down earlier when we had a wildfire evacuation!
Nice work.
I'm almost afraid to try Gargoyle 1.5...
Cheers,
John
Re: Successfully flashed a router? Tell Us!
Posted: Thu Dec 01, 2011 11:19 am
by pigstacho
Hi,
Just finished a post with the steps to flash DIR-615 E4 with 1.4.3/1.5.0
http://www.gargoyle-router.com/phpbb/vi ... f=8&t=2026
It has been working nicely for more than week.
Great Work Gargoyle!!!!
Eduardo Peccorini
Re: Successfully flashed a router? Tell Us!
Posted: Wed Dec 07, 2011 5:16 pm
by theWhip
Hi,
just finished flashing my TP-Link 1043DN 1.8 to Gargoyle 1.4.4 stable.
Re: Successfully flashed a router? Tell Us!
Posted: Mon Dec 12, 2011 11:09 pm
by chateau
Gargoyle 1.5.1 for DIR-601 A1 also works on a DIR-615 E3.
See Topic
http://www.gargoyle-router.com/phpbb/vi ... f=8&t=2026
Re: Successfully flashed a router? Tell Us!
Posted: Fri Jan 06, 2012 7:38 am
by cjrivsua
Successfully flashed: Gargoyle v1.3 (old version without: Client+AP mode and without USB support) on Comtrend CT-5361(HG536+) and Comtrend CT-536+ too, with this firmware from de genial user "Succo":
http://www.megaupload.com/?d=M5UGW1M3
Hardware Type:
CPU: BCM6348@240MHz (Broadcom BCM6348KPBG, Board ID: 96348GW-11)
RAM: 16MB SDRAM (Hynix HY57V283220TP-7)
Flash: 4MB/32Mbit (Macronix MX29LV320CBTC-70G)
Switch: 4x10/100Mbps (Broadcom BCM5325EKQM)
WiFi B/G: miniPCI 54Mbps (Broadcom BCM4306KFB)
Re: Successfully flashed a router? Tell Us!
Posted: Wed Jan 11, 2012 11:18 am
by Nilist
Successfully flashed TL-WR841 v7.2 with Gargoyle 1.4.5 for v5
Had to go through OpenWRT to install (see other thread)
Happy as a bunny for now, but hope to see official support for v7.2 at a later stage
Re: Successfully flashed a router? Tell Us!
Posted: Wed Jan 11, 2012 11:59 am
by hnl_dk
Nilist wrote:Successfully flashed TL-WR841 v7.2 with Gargoyle 1.4.5 for v5
Had to go through OpenWRT to install (see other thread)
Happy as a bunny for now, but hope to see official support for v7.2 at a later stage
Nice work... a link to the post you made in the other thread:
http://www.gargoyle-router.com/phpbb/vi ... 193#p10193
Re: Successfully flashed a router? Tell Us!
Posted: Sun Jan 29, 2012 8:12 pm
by mehtab
Successfully flashed 901nd v1 access point with 941nd v4 bin! I used it because both routers have same processor, ram, flash and wireless card. Only difference is number of lan ports.
Re: Successfully flashed a router? Tell Us!
Posted: Sun Feb 05, 2012 6:26 pm
by RedWolf
Just flashed my D-link DIR-825 B1. Went from stock 2.06NA FW to gargoyle_1.5.3-ar71xx-dir-825-b1-squashfs-factory.bin via the stock upgrade page.
Internet connection is 16/2 cable. Running 2.4 and 5G radios the speed tests are as good as the wired speed tests. (full speeds)
Re: Successfully flashed a router? Tell Us!
Posted: Sat Feb 11, 2012 7:54 am
by colinkhalid
I have successfully flashed a TP-Link MR 3420 router with the following image :
gargoyle_1.5.3-ar71xx-tl-mr3420-v1-squashfs-factory.bin
Everything apart from the USB side of things everything is working. That is to say USB modems and USB mass storage devices are not found by the firmware. I realize that many additional packages are needed and I have attempted to install the necessary packages but eventual I run out of memory before I can get all that is needed installed. If Iam understanding the command FREE correctly there is only about 100 k free after a clean flash
As I use only USB modems I have got around this problem attaching another router (Dlinik DIR 412) to the WAN port of the MR3420 and plugging the modem into it.
So it may not be possible to use the USB port unless some stuff such as kmod-usb serial , kmod-usb-core ect are built into the image