Page 1 of 1

Problem loading 1.10 on WRT3200ACM Rango

Posted: Sun Mar 04, 2018 9:26 pm
by rrradant
Hi everyone. I'm trying to install latest Gargoyle on WRT3200ACM and it hangs every time. I need to do a 30-30-30 to get back to factory firmware. What is weird is that the default ip of the router after reset is 10.138.218.12 rather than the typical 192.168.1.1 I have updated the factory firmware and tried Gargoyle 1.9.2 but no luck. Any ideas? Is there a special process / name of the firmware file required? Thanks.

Re: Problem loading 1.10 on WRT3200ACM Rango

Posted: Sun Mar 04, 2018 9:46 pm
by Lantis
Was your device manufactured around December 2017 or later? This information should be on the box.
If so it is probably not compatible with current Gargoyle images.
If you confirm this is the issue, I’ll attempt to work on the fix and you can be the guinea pig if you like. However it is possible that it cannot be easily backported to Gargoyle in which case you might have to wait.


For future reference, “30 30 30” does nothing.
The correct recovery procedure on your device is a triple power flip.
https://wiki.openwrt.org/toh/linksys/wr ... e_recovery

Re: Problem loading 1.10 on WRT3200ACM Rango

Posted: Mon Mar 05, 2018 2:13 pm
by rrradant
I contacted Linksys and they said the manufacturing date is November 24, 2017. Based on my failed efforts, the window of problems can be pushed back a bit. I really have no interest in working too hard to get the box operational, I'd rather get my refund. I appreciate the information and offer to help.

The 30/30/30 did get me back to the Linksys firmware. After trying to load Gargoyle 1.10 all I would get is a flashing power light with no connectivity. The 10 second hold down of the reset button did nothing, and repeated powering cyclings were of no good (did not try the 3X power flip). I went back to my old DD-WRT habits with 30/30/30 and it brought up the stock firmware. I will try the triple power flip this evening.

Thanks.

Re: Problem loading 1.10 on WRT3200ACM Rango

Posted: Mon Mar 05, 2018 4:06 pm
by Lantis
No problem.

The key issue is when manufacturers silently update internal components (in this case the flash memory chip) and leave the hardware revision the same.
Same thing happened with the Archer C7 routers but they were much harder to recover.

I hope your refund is painless.

Re: Problem loading 1.10 on WRT3200ACM Rango

Posted: Mon Mar 05, 2018 6:02 pm
by gu3d3s
Hello,

There are already FW options for the new WRT3200, I believe that Gargoyle will soon be using this patch too, for now I can talk about the DD-WRT ultima Vs. or the David's VS LEDE made for the WRT linksys line.

And do not ever use 30,30,30 as this can turn your WRT3200 into a permanent brick, follow the instructions suggested by @Lantis

I use this router too, and I'm available to help wherever possible.

Re: Problem loading 1.10 on WRT3200ACM Rango

Posted: Mon Mar 05, 2018 9:56 pm
by rrradant
Good to know about the 30/30/30. I don't think I will wait for the WRT3200ACM patches, probably get another TP-Link Archer C7. I have setup V2's and V3's, but is there a V4 out that is problematic?

Re: Problem loading 1.10 on WRT3200ACM Rango

Posted: Tue Nov 27, 2018 12:59 am
by coits
Hi Lantis,

Are there any isuses with wrt3200acm firmware 1.10, I just bought one and not sure, what firmware to flash? please guide to avoid any brick.

Thanks

Re: Problem loading 1.10 on WRT3200ACM Rango

Posted: Tue Nov 27, 2018 3:32 am
by Lantis
Yes. Use 1.11.0 RC4. That should work just fine :)

Re: Problem loading 1.10 on WRT3200ACM Rango

Posted: Thu Nov 29, 2018 10:41 pm
by coits
Lantis wrote:Was your device manufactured around December 2017 or later? This information should be on the box.
If so it is probably not compatible with current Gargoyle images.
If you confirm this is the issue, I’ll attempt to work on the fix and you can be the guinea pig if you like. However it is possible that it cannot be easily backported to Gargoyle in which case you might have to wait.


For future reference, “30 30 30” does nothing.
The correct recovery procedure on your device is a triple power flip.
https://wiki.openwrt.org/toh/linksys/wr ... e_recovery
Hi Lantis,

I just bought wrt3200-acm ca and there's no info if this is version1.

Are there still any issue with those devices manufactured around Dec. 2017 or later?

Please advise, really appreciate your input.

Thank you

Re: Problem loading 1.10 on WRT3200ACM Rango

Posted: Thu Nov 29, 2018 11:55 pm
by Lantis
Yes, if you use 1.10 or earlier
No, if you use 1.11 or later

Technically it isn’t a “problem”, it just doesn’t work. The router will fail to boot, and when it does this 3 times it will revert back to how it was. That’s why I like these devices, they’re quite hard to break.