USB transfer rate -1mbps

If your problem doesn't fall into one of the other categories, report it here.

Moderator: Moderators

Post Reply
SuD
Posts: 4
Joined: Wed Oct 16, 2013 1:10 pm

USB transfer rate -1mbps

Post by SuD »

speed.jpg
speed.jpg (46.37 KiB) Viewed 6572 times
Hi! I have a TP-Link wdr4300 v1 and just installed the gargoyle. It is like this:

Device Name:Gargoyle
Gargoyle Version:1.6.0
Model:TP-Link TL-WDR4300 v1
Device Configuration:Gateway
Memory Usage:25.4MB / 123.7MB (20.5%)
Connections:196/4096
CPU Load Averages:0.30 / 0.77 / 0.79 (1/5/15 minutes)

Wireless Mode:AP+WDS
2.4 GHz Access Point SSID:THEBASTOS
5GHz Access Point SSID:THEBASTOS5GHZ

I have a Seagate 2tb HD NTFS on its USB port shared. It's like this in the settings:

HDREDE /dev/sda1 / CIFS+FTP+NFS

My notebook shows the wireless signal 100% at 150mbps, but the file transfer is less than 1mbps, like in the picture attached. It took more than 30 minutes to transfer the file =/

I don't want a super speed, but at least a 5mbps transfer rate.

Am I doing something wrong?

User avatar
DoesItMatter
Moderator
Posts: 1373
Joined: Thu May 21, 2009 3:56 pm

Re: USB transfer rate -1mbps

Post by DoesItMatter »

To test what transfer rates your router would support, first do
some WIRED transfer rate testing.

That will give you your benchmark on what your router/USB HD
combo can give you as transfer rate for max speed.

Next, try a file transfer over wireless, but make sure you are
within 6 feet (2 meters) of the router to verify that it's not your
wireless signal holding you back.

Once you perform those 2 tests, you should be able to figure out
what kind of transfer rates you will get.
:twisted: Soylent Green Is People! :twisted:
2x Asus RT-N16 = Asus 3.0.0.4.374.43 Merlin
2x Buffalo WZR-HP-G300NH V1 A0D0 = Gargoyle 1.9.x / LEDE 17.01.x
2x Engenius - ESR900 Stock 1.4.0 / OpenWRT Trunk 49400

mates
Posts: 128
Joined: Mon Nov 14, 2011 7:53 am

Re: USB transfer rate -1mbps

Post by mates »

Hi

I have similar issue

i have WNDR3700V2 - with USB2

when i plug USB disk to PC than i can copy data 30MB/s

i have PC connected via LAN (1Gbit) to router and on router i have USB disk connected
when i run copying data to disk than i got speed about 2.5MB/s

Image

how to get better speed?

deathrider
Posts: 1
Joined: Mon Jun 02, 2014 3:22 am

Re: USB transfer rate -1mbps

Post by deathrider »

I have the same problem. My configuration is: Cisco/Linksys WRT160NL + Maxtor Basics 500Bg. Wired or wireless is the same behaviour.

Edit: I am using Gargoyle 1.6.1. I have noted that during a transfer the web interface become slow.
Cisco/Linksys WRT160NL with Gargoyle 1.6.1

n0pin
Posts: 129
Joined: Thu Jan 09, 2014 6:39 am

Re: USB transfer rate -1mbps

Post by n0pin »

Most probably CPU is bottlenecking transfer.

User avatar
DoesItMatter
Moderator
Posts: 1373
Joined: Thu May 21, 2009 3:56 pm

Re: USB transfer rate -1mbps

Post by DoesItMatter »

CPU can be an issue, but another issue is NTFS

Gargoyle/OpenWRT is linux based

You WILL get better performance if you use EXT3/EXT4 format

You WILL get REDUCED performance using NTFS format drives

http://www.gargoyle-router.com/phpbb/vi ... f=5&t=1109

See my post there for transfer testing I did a while back

EXT3/EXT4 format is at least 2x-3x faster than NTFS

You can get Linux Live CD's (Ubuntu, Knoppix, etc)
Boot with the Live CD/DVD
Re-format your external drive to EXT4 AFTER you back it up

Also keep in mind, only the newest routers have USB3 ports
Most still have USB2 ports, so you are limited there as well
:twisted: Soylent Green Is People! :twisted:
2x Asus RT-N16 = Asus 3.0.0.4.374.43 Merlin
2x Buffalo WZR-HP-G300NH V1 A0D0 = Gargoyle 1.9.x / LEDE 17.01.x
2x Engenius - ESR900 Stock 1.4.0 / OpenWRT Trunk 49400

Post Reply