Restrictions and DHCP menus goes after recover

[tals]

I've gone from 1.51 to 1.53

Restrictions seems to have gone and also setting of static ip's, which can't be right. Can someone else confirm these are issues or not that came with 1.53 - might have to go to 1.5.2

Router is a Netgear 3700 v2

[hnl_dk]

I've gone from 1.51 to 1.53

Restrictions seems to have gone and also setting of static ip's, which can't be right. Can someone else confirm these are issues or not that came with 1.53 - might have to go to 1.5.2

Router is a Netgear 3700 v2

Try to go to
Firewall->Restrictions
You should be able to find it there.

You think of setting a dynamically allocated static IP address?
Try to go to
Connection->DHCP
You should be able to find it there.

Please return and tell if you can find it, or if it is simply just not working.
Please report the problems in the respective subforums.

[tals]

Under firewall I now have

Firewall
Connection Limits
QoS (Upload)
QoS (Download)

Under Connection:
Connection
Basic
Tor
Dynamic DNS
Routing
Wake on LAN

ON 1.5.1 menus were as you described

[hnl_dk]

...
ON 1.5.1 menus were as you described

Is the router setup as a "gateway" or a "Wireless Bridge/Repeater"?
If it is setup as a "gateway", then try to reupgrade the firmware.

[tals]

Menu items now missing from firewall and connection

Firewall only shows:
Firewall
Connection Limits
QoS (Upload)
QoS (Download)

Connection only shows:
Connection
Basic
Tor
Dynamic DNS
Routing
Wake on LAN

Previously router was on 1.5.1 with restrictions and dhcp in their respective menus

[tals]

...
ON 1.5.1 menus were as you described

Is the router setup as a "gateway" or a "Wireless Bridge/Repeater"?
If it is setup as a "gateway", then try to reupgrade the firmware.

It's gateway, looks like the issue is the restore of the configuration. I reloaded firmware, checked and all menu's were correct and present. Then restored configuration and the menu items went.

Looks like I need to reset and then reinput the settings

[mates]

strange I have it.

I have netgear WNDR3700v2

but I remember that I had similar issue I see only status and system ... my resolution was to upgrade same firmware again ... mayby it will help you

cross fingers

[hnl_dk]

...
ON 1.5.1 menus were as you described

Is the router setup as a "gateway" or a "Wireless Bridge/Repeater"?
If it is setup as a "gateway", then try to reupgrade the firmware.

It's gateway, looks like the issue is the restore of the configuration. I reloaded firmware, checked and all menu's were correct and present. Then restored configuration and the menu items went.

Looks like I need to reset and then reinput the settings

okay
Good that you found the solution.
I have "just" used my hack to save the settings, so it is a long time since I have used the restore function.

[DoesItMatter]

It's gateway, looks like the issue is the restore of the configuration. I reloaded firmware, checked and all menu's were correct and present. Then restored configuration and the menu items went.

Looks like I need to reset and then reinput the settings

This happens when upgrading occasionally

It's not always repeatable, but if this ever occurs, usually you just
need to reset to defaults and re-configure from scratch.

[tals]

I reset the firmware to default config, still same issue. Reloaded the firmware all menus restored back correctly. I then restored the config which caused the menus to go again. Restored and am reinputting the results in again.

I'm guessing the config is corrupting it - not huge issue, strange though