Time based restrictions using UMT not local?

If your problem doesn't fall into one of the other categories, report it here.

Moderator: Moderators

stevebtas
Posts: 16
Joined: Tue Jun 02, 2015 4:06 am

Re: Time based restrictions using UMT not local?

Post by stevebtas »

Yep, that was it. QoS was enabled with a 10Mb link limit. Disabling that gets me back to similar performance to the gateway for speedtest and ping (is this a default with the new build?).
Not sure this would account for some of the slowness that seemed to be happening last night to my HASS box but will keep an eye on it over the weekend and see if anything crops up. I’ve also uninstalled the adblock plugin for the moment just to reduce potential variables.
WNDR3800 Gargoyle v1.11
D-Link DIR-868L (wifi access point, standard DLink software)

stevebtas
Posts: 16
Joined: Tue Jun 02, 2015 4:06 am

Re: Time based restrictions using UMT not local?

Post by stevebtas »

Ok, ran it for 24 hours with no problems then reinstalled and reenabled the adblock plugin. After which had trouble connecting to internet or even the router. I suspect there may be a compatibility issue between the new build and adblock plugin. Even after uninstalling it again the router response via the web interface is very flaky and sluggish
WNDR3800 Gargoyle v1.11
D-Link DIR-868L (wifi access point, standard DLink software)

ispyisail
Moderator
Posts: 5185
Joined: Mon Apr 06, 2009 3:15 am
Location: New Zealand

Re: Time based restrictions using UMT not local?

Post by ispyisail »

factory reset?

start again?

RomanHK
Posts: 794
Joined: Sat May 04, 2013 4:18 pm
Location: Czech Republik

Re: Time based restrictions using UMT not local?

Post by RomanHK »

If you have a problem with AdBlock, please read this post first: viewtopic.php?f=14&t=11829&start=160#p52151

AdBlock takes a lot of system resources, so be careful.
Turris Omnia with OpenWrt 21.02 - Tested
Linksys WRT3200ACM with Gargoyle 1.13.x
TL-WR1043ND v2 with Gargoyle 1.10.0

http://gargoyle.romanhk.cz custom builds by gargoyle users

stevebtas
Posts: 16
Joined: Tue Jun 02, 2015 4:06 am

Re: Time based restrictions using UMT not local?

Post by stevebtas »

Did a reflash back to the development version but still getting some dropouts where the web interface comes up as page not found when navigating between screens.
Reflashed again back to the release version of 1.11 and it seems to be stable and a lot more responsive. I had been running adblock on 1.11 before the timezone issue without any apparent problems.
At the moment memory use is at 19% and processor load is at zero. Haven't been game to reinstall adblock - had enough excitement this weekend :-)
WNDR3800 Gargoyle v1.11
D-Link DIR-868L (wifi access point, standard DLink software)

ispyisail
Moderator
Posts: 5185
Joined: Mon Apr 06, 2009 3:15 am
Location: New Zealand

Re: Time based restrictions using UMT not local?

Post by ispyisail »

Did a reflash back to the development version
which version?

stevebtas
Posts: 16
Joined: Tue Jun 02, 2015 4:06 am

Re: Time based restrictions using UMT not local?

Post by stevebtas »

The one i had already downloaded.
Gargoyle Version:1.11.X (Built 20190426-2024 git@ddc7c0ba)
WNDR3800 Gargoyle v1.11
D-Link DIR-868L (wifi access point, standard DLink software)

ispyisail
Moderator
Posts: 5185
Joined: Mon Apr 06, 2009 3:15 am
Location: New Zealand

Re: Time based restrictions using UMT not local?

Post by ispyisail »

Try this one

viewtopic.php?f=14&t=12002

1.11.0.x gargoyle-ispy 2019-May-05 03

Post Reply