yellow triangle after installing gargoyle?(tp link wr740n)

nicholes · Post by **nicholes** » Tue Sep 22, 2015 10:30 am

I am connected via LAN to WAN after installing gargoyle i am getting yellow triangle with exclamation mark on internet connection. I am very new in it but if you guide me i will make my way please help me..

I also did not take backup before installing Gargoyle of my tp link router. also tell me if i could go back to my previews tp link firmware from its site.

Please subscribe to my thread to help me I bought a brand new router only for gargoyle.

Thanks in advance

Post by **tapper** » Tue Sep 22, 2015 11:34 am

Hi there mate you will have to giv us a bit more info there. Like what modem do you have and how dus it connect to the inter net. what router do you have and whitch file did you use to flash. what lites are lit up on the frunt of your router? One thing you can try is to un plug your router and modem and then plug them back in to see if your router can then get a IP from your modem.

nicholes · Post by **nicholes** » Tue Sep 22, 2015 11:38 pm

tapper wrote:Hi there mate you will have to giv us a bit more info there. Like what modem do you have and how dus it connect to the inter net. what router do you have and whitch file did you use to flash. what lites are lit up on the frunt of your router? One thing you can try is to un plug your router and modem and then plug them back in to see if your router can then get a IP from your modem.

I am using tp-link tl-wr740n ver 4.27 (only router not modem)

i flashed it with gargoyle_1.8.0-ar71xx-generic-tl-wr740n-v4-squashfs-factory.bin

i am trying to the internet using my (binatone 850w) MODEM > lan to my tplink WAN >and then tplink lan wire goes to my pc

before installing this i had a working connection in the above mode

see this image for litup in my router in my router instead of wirless lit lan lit work( as i have disablled wireless)

https://r00m.files.wordpress.com/2012/0 ... _front.jpg

NOTE:- I can go into my tp link router but not in my binatone modem when both are connected

i have changed my tp link router addresss to 192.168.1.10

and binatone modem to 192.168.1.50

(assuming that they may confilct each other if they have same router ips) as i am noob i tried it
please help

nicholes · Post by **nicholes** » Tue Sep 22, 2015 11:56 pm

i am using win 7 please help

Post by **Lantis** » Wed Sep 23, 2015 12:05 am

What connection mode are you using? PPPoE or DHCP?

nicholes · Post by **nicholes** » Wed Sep 23, 2015 1:29 am

Lantis wrote:What connection mode are you using? PPPoE or DHCP?

DHPC in tp Link

Post by **Lantis** » Wed Sep 23, 2015 2:05 am

i think you'll have to put them on different subnets

nicholes · Post by **nicholes** » Wed Sep 23, 2015 2:22 am

Lantis wrote:i think you'll have to put them on different subnets

I had 255.255.255.0

I changed it to 255.255.0.0

Under Local Network / LAN in gargoyle

It did not work

I don't know if did right or not as i am new in it

nworbnhoj · Post by **nworbnhoj** » Wed Sep 23, 2015 2:25 am

http://www.gargoyle-router.com/wiki/dok ... ario-modem

nicholes · Post by **nicholes** » Wed Sep 23, 2015 2:42 am

nworbnhoj wrote:http://www.gargoyle-router.com/wiki/dok ... ario-modem

I tried exactly same setting to my tp Link but I am still getting yellow triangle

Gargoyle Forum

yellow triangle after installing gargoyle?(tp link wr740n)

yellow triangle after installing gargoyle?(tp link wr740n)

Re: yellow triangle after installing gargoyle?(tp link wr740

Re: yellow triangle after installing gargoyle?(tp link wr740

Re: yellow triangle after installing gargoyle?(tp link wr740

Re: yellow triangle after installing gargoyle?(tp link wr740

Re: yellow triangle after installing gargoyle?(tp link wr740

Re: yellow triangle after installing gargoyle?(tp link wr740

Re: yellow triangle after installing gargoyle?(tp link wr740

Re: yellow triangle after installing gargoyle?(tp link wr740

Re: yellow triangle after installing gargoyle?(tp link wr740