yellow triangle after installing gargoyle?(tp link wr740n)

[francisuk1989]

Try this On the TP-Link Router

Go to Connection > Basic
Go to Local Network / LAN (bottom)

Change

Router IP: 10.0.0.254
Subnet Mask: 255.255.255.0
DNS Servers: Default DNS Servers

Then

Go to Connection > Basic
DHCP
Start 1
end 252

Save changes, Wait 10 minutes then reboot your Modem and Router.

You should see you LAN IP somewhere between 10.0.0.1 - 10.0.0.252

If you have issues port forwarding then you need to go into the bitatone modem then setup a DMZ, The DMZ IP would be the WAN IP on the TP-Link router and you can see this by going into the TP-Link router then Connection > Basic > Internet / WAN and see Current IP: for example 192.168.0.10 << this is what you need to setup in the Bitatone Modem DMZ.

[danymarc]

Go to Connection > Basic
DHCP
Start 1
end 252
bitatone modem

bitatone doing DHCP and 740 too that will result in double NAT

[nicholes]

All i think is my settings problem.

i would install gargoyle one more time and try a bit more ..

please be with me, subscribe to my thread.

I will do it tomorrow.

Thank you all for quick and kind replies.

[danymarc]

All i think is my settings problem.
i would install gargoyle one more time and try a bit more

Before you have to decide who is doing the DHCP right now bitatone is doing the DHCP pool and using all the ips in it, I posted you the change you have to do, to shorten the pool, in this case Gargoyle should be set as AP, to do so, Connection,/BASIC/Internet / WAN/Connect Via/Disable
Wan Ethernet Port/Bridge to Lan
Local Network / LAN
Router IP:192.168.1.2
Subnet Mask 255.255.255.0
Gateway:192.168.1.1
DNS Servers: Google DNS servers
Wireless Acces Point AP
DHCP/ LAN DHCP Server Enabled UNTICK THIS BOX
Connect to any port from bitatone the five ports are ethernet cause you Bridged Wan Ethernet Port/ to Lan.

If you decide Gargoyle to do the DHCP, disable it in bitatone and set Gargoyle as router just change Gargole ip to 192.168.2.2

[francisuk1989]

Go to Connection > Basic
DHCP
Start 1
end 252
bitatone modem

bitatone doing DHCP and 740 too that will result in double NAT

Not if the TP-Link/Gargoyle router was on 10.0.0.0/8 subnet and bitatone beening on the 192.168.1.0/24 is two separate networks

so basicly
TP-Link/Gargoyle Router = Clients IP would be in range of 10.0.0.1-10.0.0.252
bitatone modem = 192.168.1.1-192.168.1.253

[danymarc]

Not if the TP-Link/Gargoyle router was on 10.0.0.0/8 subnet and bitatone beening on the 192.168.1.0/24 is two separate networks

unless you turn off NAT on one of the routers, still is double NAT

[nicholes]

Hi, all

I have decided to stay with stock right now. as i am afraid of bricking my router and i don't have enough knowledge also .

however i would try gargoyle in future. may be when i would get another spare router.

thanks for all who help me.

Special thanks to 4 great people in this community are

tapper
Lantis
danymarc
francisuk1989

and thanks to all the forum members for such a kind and quick help.

[Lantis]

No worries mate. Sorry we couldn't get you sorted this time.

Look forward to hearing from you in the future.