Try this On the TP-Link Router
Go to Connection > Basic
Go to Local Network / LAN (bottom)
Change
Router IP: 10.0.0.254
Subnet Mask: 255.255.255.0
DNS Servers: Default DNS Servers
Then
Go to Connection > Basic
DHCP
Start 1
end 252
Save changes, Wait 10 minutes then reboot your Modem and Router.
You should see you LAN IP somewhere between 10.0.0.1 - 10.0.0.252
If you have issues port forwarding then you need to go into the bitatone modem then setup a DMZ, The DMZ IP would be the WAN IP on the TP-Link router and you can see this by going into the TP-Link router then Connection > Basic > Internet / WAN and see Current IP: for example 192.168.0.10 << this is what you need to setup in the Bitatone Modem DMZ.
yellow triangle after installing gargoyle?(tp link wr740n)
Moderator: Moderators
-
- Posts: 30
- Joined: Thu Sep 24, 2015 4:46 am
- Location: United Kingdom
- Contact:
Re: yellow triangle after installing gargoyle?(tp link wr740
TP-Link TL-WDR3600 v1.5 (ar71xx)
EE Brightbox 1/Arcadyan AR7516 (BCM63xx)
MK RB750r2 - OpenWrt Snapshot ar71xx
D-Link DIR-615 D2 - OpenWrt (ramips/rt305x)
AWS Region Latency Checker # http://awsspeedtest.xvf.dk
EE Brightbox 1/Arcadyan AR7516 (BCM63xx)
MK RB750r2 - OpenWrt Snapshot ar71xx
D-Link DIR-615 D2 - OpenWrt (ramips/rt305x)
AWS Region Latency Checker # http://awsspeedtest.xvf.dk
Re: yellow triangle after installing gargoyle?(tp link wr740
bitatone doing DHCP and 740 too that will result in double NATfrancisuk1989 wrote: Go to Connection > Basic
DHCP
Start 1
end 252
bitatone modem
Re: yellow triangle after installing gargoyle?(tp link wr740
All i think is my settings problem.
i would install gargoyle one more time and try a bit more ..
please be with me, subscribe to my thread.
I will do it tomorrow.
Thank you all for quick and kind replies.
i would install gargoyle one more time and try a bit more ..
please be with me, subscribe to my thread.
I will do it tomorrow.
Thank you all for quick and kind replies.
Re: yellow triangle after installing gargoyle?(tp link wr740
Before you have to decide who is doing the DHCP right now bitatone is doing the DHCP pool and using all the ips in it, I posted you the change you have to do, to shorten the pool, in this case Gargoyle should be set as AP, to do so, Connection,/BASIC/Internet / WAN/Connect Via/Disablenicholes wrote:All i think is my settings problem.
i would install gargoyle one more time and try a bit more
Wan Ethernet Port/Bridge to Lan
Local Network / LAN
Router IP:192.168.1.2
Subnet Mask 255.255.255.0
Gateway:192.168.1.1
DNS Servers: Google DNS servers
Wireless Acces Point AP
DHCP/ LAN DHCP Server Enabled UNTICK THIS BOX
Connect to any port from bitatone the five ports are ethernet cause you Bridged Wan Ethernet Port/ to Lan.
If you decide Gargoyle to do the DHCP, disable it in bitatone and set Gargoyle as router just change Gargole ip to 192.168.2.2
-
- Posts: 30
- Joined: Thu Sep 24, 2015 4:46 am
- Location: United Kingdom
- Contact:
Re: yellow triangle after installing gargoyle?(tp link wr740
Not if the TP-Link/Gargoyle router was on 10.0.0.0/8 subnet and bitatone beening on the 192.168.1.0/24 is two separate networksdanymarc wrote:bitatone doing DHCP and 740 too that will result in double NATfrancisuk1989 wrote: Go to Connection > Basic
DHCP
Start 1
end 252
bitatone modem
so basicly
TP-Link/Gargoyle Router = Clients IP would be in range of 10.0.0.1-10.0.0.252
bitatone modem = 192.168.1.1-192.168.1.253
TP-Link TL-WDR3600 v1.5 (ar71xx)
EE Brightbox 1/Arcadyan AR7516 (BCM63xx)
MK RB750r2 - OpenWrt Snapshot ar71xx
D-Link DIR-615 D2 - OpenWrt (ramips/rt305x)
AWS Region Latency Checker # http://awsspeedtest.xvf.dk
EE Brightbox 1/Arcadyan AR7516 (BCM63xx)
MK RB750r2 - OpenWrt Snapshot ar71xx
D-Link DIR-615 D2 - OpenWrt (ramips/rt305x)
AWS Region Latency Checker # http://awsspeedtest.xvf.dk
Re: yellow triangle after installing gargoyle?(tp link wr740
unless you turn off NAT on one of the routers, still is double NATfrancisuk1989 wrote:Not if the TP-Link/Gargoyle router was on 10.0.0.0/8 subnet and bitatone beening on the 192.168.1.0/24 is two separate networks
Re: yellow triangle after installing gargoyle?(tp link wr740
Hi, all
I have decided to stay with stock right now. as i am afraid of bricking my router and i don't have enough knowledge also .
however i would try gargoyle in future. may be when i would get another spare router.
thanks for all who help me.
Special thanks to 4 great people in this community are
tapper
Lantis
danymarc
francisuk1989
and thanks to all the forum members for such a kind and quick help.
I have decided to stay with stock right now. as i am afraid of bricking my router and i don't have enough knowledge also .
however i would try gargoyle in future. may be when i would get another spare router.
thanks for all who help me.
Special thanks to 4 great people in this community are
tapper
Lantis
danymarc
francisuk1989
and thanks to all the forum members for such a kind and quick help.
Re: yellow triangle after installing gargoyle?(tp link wr740
No worries mate. Sorry we couldn't get you sorted this time.
Look forward to hearing from you in the future.
Look forward to hearing from you in the future.
http://lantisproject.com/downloads/gargoyle_ispyisail.php for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.
Please be respectful when posting. I do this in my free time on a volunteer basis.