yellow triangle after installing gargoyle?(tp link wr740n)

[Lantis]

put the modem onto
192.168.1.xxx
and the gargoyle onto
192.168.2.xxx

notice the third octet has changed.

[nicholes]

put the modem onto
192.168.1.xxx
and the gargoyle onto
192.168.2.xxx

notice the third octet has changed.

assuming your are talking about modem ip and router ip

i changed them as you mentioned but i am facing still same issue please help

[nicholes]

I also tried to changed its static ip as you mentioned but still no change

see images

[Lantis]

Why is the gateway a loop back address?
Shouldn't it be the address of the modem?

[nicholes]

Why is the gateway a loop back address?
Shouldn't it be the address of the modem?

I am really really sorry

I dont understand please make more clear if possible

Thanks you for kind and a quick reply

[Lantis]

In gargoyle, your "Gateway" address (below Static IP and Subnet) should be 192.168.1.1 (the address you set on your modem).

You currently have it set to 127.0.0.1 which is a "loopback". That means it points at itself.

[nicholes]

In gargoyle, your "Gateway" address (below Static IP and Subnet) should be 192.168.1.1 (the address you set on your modem).

You currently have it set to 127.0.0.1 which is a "loopback". That means it points at itself.

Thanks again for quick reply

I just changed it but problem is still there

what change i should make now ??


Sorry, the board attachment quota has been reached.

i cannot post image

[danymarc]

what change i should make now ??

I recreated your scenario
my ISP Gateway is 192.168.1.254 and ISP DHCP is 192.168.1.50 to 192.168.1.253 see screenshot, the only issue i found is if i used ISP DNS I could not surf the web until I changed to Google DNS

share image

[nicholes]

Thanks

Right now I have gone back to stock firmware.

I would try your scenario.

Please confirm that yellow triangle can be solved by just making changes like you made

Or it was not the problem in my tp Link router or gargoyle that I installed.

I mean I would install gargoyle if anyone confirm that it is possible to solve yellow triangle

Also notice that in my tp Link router I am connected via dynamic IP that is working perfectly.

[danymarc]

Also notice that in my tp Link router I am connected via dynamic IP that is working perfectly.

My advise, stay in Stock, no one is to confirm you any, and who ever does its a guess, every network scenario it's dif. and your issue is a miss configuration, and only you can solve it, there are lots of mistakes in your setting, from what I see in your picture from your modem 192.168.1.1 it's your ISP gateway, DHCP is enable in modem, and ipool is from 192.168.2 to 192.168.253 there no room you had to change 192.168.1.2 to 192.168.1.50 so you have IPs out of DHCP pool from 2 to 50, once that done, your modem is providing Internet to Lap via Lan cable, all you need it its to set Gargoyle 740 to AP cause your modem it's taking care of the DHCP or as router with Googles DNS or as the last scenario you tried but as you can see your lack of network knowledge addressed you wrong, in Gargoyle in static ip you wrote 192.168.2.10 should be 192.168.1.2 or any number you like between 2 and 49, on subnet mask you wrote 255.255.0.0 should had been 255.255.255.0 and in Gateway you left default 127.0.0.1 should be 192.168.1.1
On local network Lan router ip you wrote 192.168.1.10 should be any ip you like but with dif subnet from ISP Gateway like 192.1682.2 you wrote too wrong subnet mask 255.255.0.0 should be 255.255.255.0 and try Googles DNS as you can see your settings where all wrong