Page 13 of 20
Re: Version 1.9.1
Posted: Wed Aug 17, 2016 6:39 pm
by rseiler
tapper wrote:flashed my c7 and had no 5 ghz had to go back to last 1.9.x
Are you talking about the v2? Did you ever figure out what was going on? I know historically there's been an issue with this, but I thought 1.9.1 supported it.
Re: Version 1.9.1
Posted: Thu Aug 18, 2016 4:04 am
by tapper
Hi mate it was the c7 v2 and it got fixt by a firstboot and reflashing. It now runs sweet as a nut. Just don't save settings if upgrading from 1.9.0
Re: Version 1.9.1
Posted: Thu Aug 18, 2016 4:00 pm
by ctsffd
Lantis wrote:Firstboot reset or reflashing 1.9.1 then try again.
Try both but doesn't help. Still back to factory default after power cycle.
Revert back to 1.6.2 and configurations retain even after power cycle.
Re: Version 1.9.1
Posted: Fri Aug 19, 2016 5:02 am
by ispyisail
ctsffd wrote:Lantis wrote:Firstboot reset or reflashing 1.9.1 then try again.
Try both but doesn't help. Still back to factory default after power cycle.
Revert back to 1.6.2 and configurations retain even after power cycle.
4 meg router?
Re: Version 1.9.1
Posted: Fri Aug 19, 2016 11:34 am
by kuss
Hi Peeps was just going to test out the new FW on my wndr3800 and noticed that there are 2 types? 1 with CH and other with out, whats CH mean?
Re: Version 1.9.1
Posted: Fri Aug 19, 2016 2:23 pm
by rseiler
kuss wrote:Hi Peeps was just going to test out the new FW on my wndr3800 and noticed that there are 2 types? 1 with CH and other with out, whats CH mean?
It's for if you're stuck with the WNDR3800CH running Charter factory firmware.
Re: Version 1.9.1
Posted: Fri Aug 19, 2016 3:21 pm
by kuss
ah ok ty
Re: Version 1.9.1
Posted: Fri Aug 19, 2016 3:42 pm
by ctsffd
ispyisail wrote:ctsffd wrote:Lantis wrote:Firstboot reset or reflashing 1.9.1 then try again.
Try both but doesn't help. Still back to factory default after power cycle.
Revert back to 1.6.2 and configurations retain even after power cycle.
4 meg router?
it isFlash ROM 8 MB/RAM 32 MB
Re: Version 1.9.1
Posted: Fri Aug 19, 2016 7:59 pm
by ninderrycomp
Just wanted to share my experience with my 1043ND v2.1. I made a backup and updated without preserving settings and that works OK, but the moment I restored my backup, the router would enter a reboot loop. Had to use a failsafe reset to get it going again. It looks like I have to migrate my settings manually
Anyone hazard a guess on why this happens? I'm using quite a few features, mainly DHCP reservation, QOS uplink and downlink rules.
http://i.imgur.com/33mvgIC.png
Seems like I'm gonna have to re-configure my router from scratch... sigh
Re: Version 1.9.1
Posted: Fri Aug 19, 2016 8:56 pm
by Lantis
You didn't mention which version you came from, but the settings were most likely not compatible.
Preserve settings is EXACTLY THE SAME as making a backup and then restoring it later.
If one was to fail (which there are many reports of this) then the other surely will as well.
You can manually restore certain settings (e.g. DHCP reservations, QOS rules) but not all of them (e.g. Network and wireless settings)
