Gargoyle Forum

For me UPNP monitoring is broken with this build, the software can't connect to the router (WDR3600).

phgerin wrote:For me UPNP monitoring is broken with this build, the software can't connect to the router (WDR3600).

more information please

is guest WLAN Quota working with 1.7.2 ?
Thanks

Thanks, finally, unknown source I.P. shown in WOL page is fixed.
Now it show internal I.P. addresses and only one Wan I.P. address

Thank you for this Eric.. i decided to give this a try on a C7 converted from a C5 converted from DDwrt -> stock -> gargoyle 172.

The router is used as an AP so most of its services are switched off except for USB (have a 500Gb NTFS disk connected) and of course dual band wireless.

First thing i noticed is that after set up, i was getting inconsistent access to the shared drive from a Windows 10 machine. Not sure why this is - maybe its just Windows as on my mbp and adnroid tablet i had no probs.

Second thing i noticed re. wireless - is that ch 100 seems gone. Using 149 and frankly I am equally happy so far. The front 2.5/5 ghz LEDs are also not functioning.

Other than that - so far so good. Can't wait for the CC release tbh.

Successfully installed on TL-WDR3600 and restored config from 1.7.x including 3G, Dynamic DNS, port forwarding, Adblock, Quotas, QoS, USB Storage.

Device Name:Gargoyle
Gargoyle Version:1.7.2
Model:TP-Link TL-WDR3600 v1
Device Configuration:Gateway
Memory Usage:28MB / 123.4MB (22.6%)
Connections:573/4096
CPU Load Averages:0.09 / 0.25 / 0.21 (1/5/15 minutes)

However, still no joy with TOR

• The TOR plugin installs, and shows as installed (on plugins.sh and gpkg list-installed)
• however TOR does not appear in GUI menu (even after reboot).
• /www/tor.sh does not exist.
• /etc/tor.firewall does exist with size = 10966.
• /www/tor/ does exist but is empty.
• gpkg remove plugin-gargoyle-tor results in "ERROR: Package plugin-gargoyle-tor is installed to destination 'plugin_root' which is not writable, cannot uninstall"

I think that things might be a little tangled now that I have tried a few things - may have to reinstall and reconfigure from scratch ....

Any other things that I can check?

5Ghz now shows up in the config for Archer C7 V2.

Bug:
In the channel config, the 2.4Ghz channel select shows 5Ghz channels and vise versa.
5Ghz channels: 1-11
2.4Ghz channels: 36-165

If I try to change 5Gz to 40Mhz its available channels dropdown goes blank.

Currently showing 2.4Gz on channel 1 and 5Ghz enabled.
Wi-Fi snoop shows channel 6 and no 5Ghz.

I think that things might be a little tangled now that I have tried a few things - may have to reinstall and reconfigure from scratch ....

I can not enable tor

Any one upgraded to 1.7.2 to TP-Link TL-WR1043N/ND V1. Any problem expected?

I have updated from version 1.7.1 to 1.7.2. Updated to 1.7.2 without preserve my settings. I restored my settings from the backup file that I saved before I updated to 1.7.2. After the restore off the settings I can no longer access the router's web interface (I get the message that the page can not be displayed). The routers work fine but I cant make any Changes to its configuration because of the missing web interface. How do I fix this problem with the missing web interface?