Page 2 of 14
Re: Version 1.7.0 - Barrier Breaker
Posted: Mon Jan 05, 2015 2:28 pm
by nieroster
First of all: Thank you Eric! Finally we get a BB build of Gargoyle!
What i've noticed is that my USB Printer does not show up in this build, using a Netgear WNDR3700 + HP Photosmart D5160.
It did work on ispyisail's build from January 3rd though.
nieroster
EDIT:
here are the log entries when plugging in the printer:
Code: Select all
Tue Jan 6 12:30:00 2015 kern.info kernel: [ 149.810000] usb 1-1: new high-speed USB device number 2 using ehci-platform
Tue Jan 6 12:30:00 2015 kern.info kernel: [ 149.970000] usblp 1-1:1.0: usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x03F0 pid 0xC402
Tue Jan 6 12:30:00 2015 kern.info kernel: [ 149.980000] usb-storage 1-1:1.2: USB Mass Storage device detected
Tue Jan 6 12:30:00 2015 kern.info kernel: [ 150.000000] scsi0 : usb-storage 1-1:1.2
Tue Jan 6 12:30:01 2015 kern.notice kernel: [ 151.000000] scsi 0:0:0:0: Direct-Access HP Photosmart D5100 1.00 PQ: 0 ANSI: 2
Tue Jan 6 12:30:01 2015 kern.notice kernel: [ 151.010000] sd 0:0:0:0: [sda] Attached SCSI removable disk
Tue Jan 6 12:30:21 2015 user.err syslog: Unkown action change
Tue Jan 6 12:30:21 2015 user.err syslog: Unkown action change
Maybe it's the integrated card reader which irritates gargoyle.
Re: Version 1.7.0 - Barrier Breaker
Posted: Mon Jan 05, 2015 3:18 pm
by zero
There seems to be problem with plugins, i can install it but I can not remove it after, using web-gui or opkg. trying to uninstall plugin from opkg result in segmentation fault.
The only plugins sucessfully installed and uninstalled is themes (in this case i use light-theme).
my details :
- plugin-root in usb flash drive formatted as ext4 in dev/sda1
- i also have swap partition in /dev/sda2
- using tp-link tl-wdr4300 v1
- tried firmware upgrade from sysupgrade or factory 1.7.0 without preserving any setting, the plugin is removed, but after I installed it again it became uninstallable.
- previous version (1.6.2 <) the plugins can be installed and removed successfully.
any ideas?
Re: Version 1.7.0 - Barrier Breaker
Posted: Mon Jan 05, 2015 3:39 pm
by ispyisail
Eric is in the Zone
It appears that he is patching as fast as you guys are reporting
Next build will be up in a few minutes
Re: Version 1.7.0 - Barrier Breaker
Posted: Mon Jan 05, 2015 3:47 pm
by phgerin
Download speed reported via UPNP is still broken after a few hours (maybe after 4GB transfert).
Re: Version 1.7.0 - Barrier Breaker
Posted: Mon Jan 05, 2015 4:32 pm
by nworbnhoj
Thank you Eric for all the great work - appreciate it!
I loaded 1.7.0 onto a TP-Link TL-WR1043N/ND v2 successfully.
However, when configured as a Gateway, the Internet/WAN interface does not offer a 3G (GSM) option despite a Huawei E160E modem being plugged into the USB port. The modem has power and the status light indicates that a 3G signal is available.
I have rolled back to Gargoyle 1.6.2 where the 3G connection works with the Huawei E160E modem.
Continued at
http://www.gargoyle-router.com/phpbb/vi ... =11&t=6563
Re: Version 1.7.0 - Barrier Breaker
Posted: Mon Jan 05, 2015 4:57 pm
by ispyisail
Re: Version 1.7.0 - Barrier Breaker
Posted: Mon Jan 05, 2015 4:59 pm
by ispyisail
nworbnhoj wrote:Thank you Eric for all the great work - appreciate it!
I loaded 1.7.0 onto a TP-Link TL-WR1043N/ND v2 successfully.
However, when configured as a Gateway, the Internet/WAN interface does not offer a 3G (GSM) option despite a Huawei E160E modem being plugged into the USB port. The modem has power and the status light indicates that a 3G signal is available.
I have rolled back to Gargoyle 1.6.2 where the 3G connection works with the Huawei E160E modem.
Can you check
just after you plug you 3g dongle in?
Re: Version 1.7.0 - Barrier Breaker
Posted: Mon Jan 05, 2015 5:22 pm
by Volaris
Thanks for the update!
I updated my Linksys WRT400N from 1.6.1 to 1.7 (it didn't like 1.6.2) and it seems to work fine. 5GHz works much better now (range and tx rate actually maxes out!).
My only concern is that CPU usage seems a bit high? Registering 0.25-0.75 (saw it go up to 1.65) CPU usage, even with low usage on my slow connection (not logging anything other than default, either). Previously I recall those numbers rarely going above 0.20. Router has a 680MHz CPU. Are these normal numbers?
Re: Version 1.7.0 - Barrier Breaker
Posted: Mon Jan 05, 2015 5:32 pm
by Andy
Flashed onto a WDR3600 and works fine so far!
Re: Version 1.7.0 - Barrier Breaker
Posted: Mon Jan 05, 2015 5:41 pm
by djt_nz
Before I start a custom build can someone confirm if the bb branch has been merged back into master. So I no longer need to do a "git checkout bb"
I don't use git much, more of a svn man, find git a bit confusing at times
