Page 6 of 13
Re: Barrier Breaker Progress
Posted: Mon Dec 08, 2014 9:42 am
by Doky
Gargoyle 1.7 Uptime: 1 days, 1 hours, 29 minutes
No problem, good work!
Re: Barrier Breaker Progress
Posted: Mon Dec 08, 2014 10:28 am
by KREAT0R
ispyisail wrote:Code: Select all
------------------------------------------------------------------
| _____ _ |
| | __ \ | | |
| | | \/ __ _ _ __ __ _ ___ _ _| | ___ |
| | | __ / _` | '__/ _` |/ _ \| | | | |/ _ \ |
| | |_\ \ (_| | | | (_| | (_) | |_| | | __/ |
| \____/\__,_|_| \__, |\___/ \__, |_|\___| |
| __/ | __/ | |
| |___/ |___/ |
| |
|----------------------------------------------------------------|
| Gargoyle version 1.7.X | OpenWrt Barrier Breaker branch |
| Gargoyle revision 9b4e0d7 | OpenWrt revision r43166 |
| Built December 07, 2014 | Target ar71xx/default |
------------------------------------------------------------------
root@Gargoyle:~#
No bin for 841nd v5?
Re: Barrier Breaker Progress
Posted: Mon Dec 08, 2014 12:23 pm
by devslashfw
ispyisail wrote:Update
http://goo.gl/W9UzMF
gargoyle_1.7.x-ar71xx-generic-wndr3800-squashfs-factory.img
gargoyle_1.7.x-ar71xx-generic-wndr3800-squashfs-sysupgrade.bin
Feeback / Tested: WNDR3800
Upgraded via web interface from:
gargoyle_1.6.2-ar71xx-generic-wndr3800-squashfs-factory.img
TO:
gargoyle_1.7.x-ar71xx-generic-wndr3800-squashfs-sysupgrade.bin
-Was able to SSH, and use the web management.
-Unable to turn on the 2.4ghz or 5ghz WiFi.
Was able to successfully revert via web interface to:
gargoyle_1.6.2-ar71xx-generic-wndr3800-squashfs-sysupgrade.img.
Re: Barrier Breaker Progress
Posted: Mon Dec 08, 2014 4:02 pm
by vladtheodor
tapper wrote:vladtheodor wrote:Anyone see that "iw reg set BO" is (global limit) decreased from 30dBm to 20dBm ? Changed back to US...
Is that meen Transmit Power? mine says 30 dBm
Yeap. Transmit power. Any alternate 20+ dBm country !?
Re: Barrier Breaker Progress
Posted: Mon Dec 08, 2014 8:42 pm
by megaslx
I'm using buffalo G450H.
I install 1.7.x from openwrt，but couldn't finish the router's inital setup.
after finish the pppoe connection and wifi setting,I can't connect the router via lan or wifi.I have to pull off the power cable and turn it on again, then the router works.....
But every time I log in the router via web gui,it still show's the init setup page(ask me to change password witch I already did,and chose language).
Re: Barrier Breaker Progress
Posted: Mon Dec 08, 2014 8:51 pm
by ispyisail
megaslx wrote:I'm using buffalo G450H.
I install 1.7.x from openwrt，but couldn't finish the router's inital setup.
after finish the pppoe connection and wifi setting,I can't connect the router via lan or wifi.I have to pull off the power cable and turn it on again, then the router works.....
But every time I log in the router via web gui,it still show's the init setup page(ask me to change password witch I already did,and chose language).
Try failsafe reset (factory reset)
Re: Barrier Breaker Progress
Posted: Mon Dec 08, 2014 11:35 pm
by Sport
Thanks ispyisail ! Good, but don't have plugin?
Device Name: Gargoyle
Gargoyle Version: 1.7.X (Built 20141206-2344 git@9b4e0d7)
Model: TP-Link TL-WR741N/ND v4
Device Configuration: Gateway
Memory Usage: 14.1MB / 28.2MB (50.1%)
Connections: 160/4096
CPU Load Averages: 0.24 / 0.19 / 0.08 (1/5/15 minutes)
Uptime: 0 days, 0 hours, 2 minutes
Current Date & Time: 12/09/14 3:32 AM UTC+7
root@Gargoyle:~#
BusyBox v1.22.1 (2014-12-07 15:02:17 NZDT) built-in shell (ash)
Enter 'help' for a list of built-in commands.
------------------------------------------------------------------
| _____ _ |
| | __ \ | | |
| | | \/ __ _ _ __ __ _ ___ _ _| | ___ |
| | | __ / _` | '__/ _` |/ _ \| | | | |/ _ \ |
| | |_\ \ (_| | | | (_| | (_) | |_| | | __/ |
| \____/\__,_|_| \__, |\___/ \__, |_|\___| |
| __/ | __/ | |
| |___/ |___/ |
| |
|----------------------------------------------------------------|
| Gargoyle version 1.7.X | OpenWrt Barrier Breaker branch |
| Gargoyle revision 9b4e0d7 | OpenWrt revision r43166 |
| Built December 07, 2014 | Target ar71xx/default |
------------------------------------------------------------------
root@(none):~#
Re: Barrier Breaker Progress
Posted: Tue Dec 09, 2014 1:31 am
by megaslx
ispyisail wrote:megaslx wrote:I'm using buffalo G450H.
I install 1.7.x from openwrt，but couldn't finish the router's inital setup.
after finish the pppoe connection and wifi setting,I can't connect the router via lan or wifi.I have to pull off the power cable and turn it on again, then the router works.....
But every time I log in the router via web gui,it still show's the init setup page(ask me to change password witch I already did,and chose language).
Try failsafe reset (factory reset)
I find another problem.
utorrent cann't connect to any seeds or peers.....
I've already enabled the upnp setting.
Re: Barrier Breaker Progress
Posted: Tue Dec 09, 2014 7:26 pm
by vladtheodor
O.K. - found a good country regulatory database here :
http://wireless.kernel.org/en/developer ... y/Database
Working for me Taiwan and Belize. Power back to 24 dBm.
Re: Barrier Breaker Progress
Posted: Wed Dec 10, 2014 7:39 am
by TOCK Chiu
Hi, I got these error message when I tried to build the code cloned from github "bb" branch:
Code: Select all
configure: WARNING: unrecognized options: --disable-nls, --disable-ipv6
configure: loading site script /home/tock/桌面/gargoyle/ar71xx-src/include/site/mips-openwrt-linux-uclibc
checking build system type... x86_64-pc-linux-gnu
checking host system type... mips-openwrt-linux-gnu
checking for a BSD-compatible install... /usr/bin/install -c
checking whether build environment is sane... yes
checking for mips-openwrt-linux-strip... mips-openwrt-linux-uclibc-strip
checking for a thread-safe mkdir -p... /bin/mkdir -p
checking for gawk... gawk
checking whether make sets $(MAKE)... yes
checking how to create a pax tar archive... gnutar
checking for grep that handles long lines and -e... /home/tock/桌面/gargoyle/ar71xx-src/staging_dir/host/bin/grep
configure: error: The kernel source directory /home/tock/桌面/gargoyle/ar71xx-src/build_dir/target-mips_34kc_uClibc-0.9.33.2/linux-ar71xx_generic/linux-3.10.49 is not patched with netlink.patch to support ipset
make[4]: *** [/home/tock/桌面/gargoyle/ar71xx-src/build_dir/target-mips_34kc_uClibc-0.9.33.2/linux-ar71xx_generic/ipset-6.11/.configured_] Error 1
make[4]: Leaving directory `/home/tock/桌面/gargoyle/ar71xx-src/package/ipset'
make[3]: *** [package/ipset/compile] Error 2
make[3]: Leaving directory `/home/tock/桌面/gargoyle/ar71xx-src'
make[2]: *** [/home/tock/桌面/gargoyle/ar71xx-src/staging_dir/target-mips_34kc_uClibc-0.9.33.2/stamp/.package_compile] Error 2
make[2]: Leaving directory `/home/tock/桌面/gargoyle/ar71xx-src'
make[1]: *** [world] Error 2
make[1]: Leaving directory `/home/tock/桌面/gargoyle/ar71xx-src'
I tried on both Arch Linux and Ubuntu 14.04.