Page 3 of 10

Re: Version 1.6.0

Posted: Fri Jan 17, 2014 6:10 am
by Ashesh
THE FIRMWARE IS BUGGY!!

my router is shown to be using custom MAC IP on the summary tab even tough it is unchecked in the connections tab.

I Upgraded from 1.5.11 while keeping the previous settings preserved.

Re: Version 1.6.0

Posted: Fri Jan 17, 2014 7:03 am
by mates
StRoMeCzEcH wrote:seems like Bandwidth Distribution is broken - shows nothing... Bandwidth Distribution Table - sum 0B


I have same issue with B/W distribution - not working (preserve settings)

also on WOL - there is still problem with 00:00:00:00:00:00 Mac address ( http://www.gargoyle-router.com/phpbb/viewtopic.php?f=6&t=2227&hilit=WoL )

Re: Version 1.6.0

Posted: Fri Jan 17, 2014 7:27 am
by StRoMeCzEcH
i had same problem when going 1.5.9 > 1.5.11 with preserve settings... on clean install it was ok.
Ashesh wrote:THE FIRMWARE IS BUGGY!!

my router is shown to be using custom MAC IP on the summary tab even tough it is unchecked in the connections tab.

I Upgraded from 1.5.11 while keeping the previous settings preserved.

Re: Version 1.6.0

Posted: Fri Jan 17, 2014 7:36 am
by Phoebus
Haven't tried 1.6.0 yet. Just letting you guys try for me. Tip, I usually do not preserve settings but back up settings before flash. Then just refer to the backup text files for settings. Not too much trouble to manually fix up the settings from the text files.

Re: Version 1.6.0

Posted: Fri Jan 17, 2014 9:54 am
by Eric
The issue with the bandwidth distribution should now be resolved, and a re-release (new images, you'll note md5sums changed) for 1.6.0. Very sorry about that.

Also since this is almost entirely a bugfix release preserving settings from 1.5.11 => 1.6.0 should not cause any problems.

Re: Version 1.6.0

Posted: Fri Jan 17, 2014 10:25 am
by Jeah
"Reconnect Mode: Connect On Demand " via PPPOE tested not work yet on my WR741N v1 :cry:

Re: Version 1.6.0

Posted: Fri Jan 17, 2014 2:50 pm
by colinjenke
I am using a TL-WR1043ND v1.1 HAVE JUST UPGRADED TO TO V 1.60. ISSUE I HAVE IS UNDER UNDER: STATUS/BANDWIDTH USAGE / PLOTS AND BANDWIDTH USAGE TABLES. Under the tab of HOST-NAME no users appear. Display ID is Blank on Host-name and IP.Therefore i cannot see who is using what data.

Hope you can help Eric
Regards
Colin

Re: Version 1.6.0

Posted: Fri Jan 17, 2014 4:03 pm
by Eric
colinjenke: Please re-download version 1.6.0. This is the same bug that was reported above, and caused me to do a re-release. This problem should not show up in the latest firmware.

Re: Version 1.6.0

Posted: Fri Jan 17, 2014 5:57 pm
by Rog66
There is still a bug in torip.sh

In lines 17 and 23 "$connect_ip" should be "$connect_ip " (note the space) Otherwise 192.168.x.2 and 192.168.x.2x and 192.168.x.2xx get counted as identical ip addresses and tor assignment fails.

Re: Version 1.6.0

Posted: Fri Jan 17, 2014 6:18 pm
by Eric
Rog66: Thanks for pointing this out. Fix committed, though I don't think it's a sufficiently major issue to do a re-release as I did for the bandwidth monitor issue. This will be included in the next release though.