Gargoyle Forum

jorgemiguel4,

About password:
- Remove power from router, then reconnect and start clicking fast on QSS button until SYS Led starts blinking very fast
- Set you computer IP to 192.168.1.2
- Connect your router using Telnet 192.168.1.1 with putty or whatever you use...

Execute the commands:
- mount_root
- passwd

You will be prompted for the new password in passwd command.

I just follow your tips (same here http://wiki.openwrt.org/doc/howto/generic.failsafe)

Its cool. Thank you ! Now, lets play with QoS

I had to revert back to 1.5.5 on my WNDR3800: on 1.5.7, wifi is quite unstable (stops working every few hours, and I didn't have enough time to investigate further as it's a production environment). More, the connection list is crowded of all the connections (almost the full nat table).

Sorry, this won't help, but it's just a report

Anyone got a problem with Rootfs on External Storage (extroot) ?

Couldn't mount as a rootfs on this branch.

Here is my fstab

First login time zone now defaults to "Gambia, Liberia, Morocco" instead of "London" ?

ispyisail: yes, it's been that way for a while. The difference is that London uses Daylight Savings Time. The "standard" +0:00 UTC time isn't used by many countries except England, but that's not quite right either since England has DST,even though it's in the reference time zone. So, the reference time zone ends up not having too many large countries that use it by default, but it's still the standard/refernece.

On my wr1043nd WAN IP address appears blank.

I thought my connection wasn't working must have tried it three times then I realised there was a connection lol.

ericwong wrote:

excelsi wrote: Can somebody tell me where i can find these logs from the command line after i established a telnet seessions to the router?

Try
logread
dmesg

Hi,

here is the output after booting in recovery mode. So far as i can see there is nothing useful for the OpenVPN Prolbem:

root@(none):/# logread
logread: can't find syslogd buffer: No such file or directory
root@(none):/# dmesg
[ 0.000000] Linux version 3.3.8 (eric@Osiris) (gcc version 4.6.3 20120201 (pr
erelease) (Linaro GCC 4.6-2012.02) ) #3 Thu Sep 20 04:21:23 EDT 2012
[ 0.000000] MyLoader: sysp=ffffffff, boardp=ffffffff, parts=ffffffff
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR9132 rev 2
[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:5.000
MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00002000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00002000
[ 0.000000] On node 0 totalpages: 8192
[ 0.000000] free_area_init_node: node 0, pgdat 802daf90, node_mem_map 8100000
0
[ 0.000000] Normal zone: 64 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 8128 pages, LIFO batch:0
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag
es: 8128
[ 0.000000] Kernel command line: board=TL-WR1043ND console=ttyS0,115200 root
fstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32
bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 29208k/32768k available (2131k kernel code, 3560k reserve
d, 409k data, 208k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, No
des=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.090000] gpiochip_add: registered GPIOs 0 to 21 on device: ath79
[ 0.100000] MIPS: machine is TP-LINK TL-WR1043ND
[ 0.360000] bio: create slab <bio-0> at 0
[ 0.370000] Switching to clocksource MIPS
[ 0.380000] NET: Registered protocol family 2
[ 0.380000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.380000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.390000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.390000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.400000] TCP reno registered
[ 0.400000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.410000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.410000] NET: Registered protocol family 1
[ 0.420000] PCI: CLS 0 bytes, default 32
[ 0.440000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.440000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY
) (c) 2001-2006 Red Hat, Inc.
[ 0.450000] msgmni has been set to 57
[ 0.460000] io scheduler noop registered
[ 0.460000] io scheduler deadline registered (default)
[ 0.470000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.490000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 0.500000] console [ttyS0] enabled, bootconsole disabled
[ 0.510000] m25p80 spi0.0: found s25sl064a, expected m25p80
[ 0.520000] m25p80 spi0.0: s25sl064a (8192 Kbytes)
[ 0.530000] 5 tp-link partitions found on MTD device spi0.0
[ 0.530000] Creating 5 MTD partitions on "spi0.0":
[ 0.540000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.540000] 0x000000020000-0x000000104a00 : "kernel"
[ 0.550000] mtd: partition "kernel" must either start or end on erase block b
oundary or be smaller than an erase block -- forcing read-only
[ 0.560000] 0x000000104a00-0x0000007f0000 : "rootfs"
[ 0.570000] mtd: partition "rootfs" must either start or end on erase block b
oundary or be smaller than an erase block -- forcing read-only
[ 0.580000] mtd: partition "rootfs" set to be root filesystem
[ 0.590000] mtd: partition "rootfs_data" created automatically, ofs=680000, l
en=170000
[ 0.600000] 0x000000680000-0x0000007f0000 : "rootfs_data"
[ 0.600000] 0x0000007f0000-0x000000800000 : "art"
[ 0.610000] 0x000000020000-0x0000007f0000 : "firmware"
[ 0.620000] Realtek RTL8366RB ethernet switch driver version 0.2.3
[ 0.740000] rtl8366rb rtl8366rb: using GPIO pins 18 (SDA) and 19 (SCK)
[ 0.740000] rtl8366rb rtl8366rb: RTL5937 ver. 3 chip found
[ 0.920000] rtl8366rb: probed
[ 0.930000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[ 1.230000] TCP cubic registered
[ 1.240000] NET: Registered protocol family 17
[ 1.240000] Bridge firewalling registered
[ 1.240000] Ebtables v2.0 registered
[ 1.250000] 8021q: 802.1Q VLAN Support v1.8
[ 1.260000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 1.270000] Freeing unused kernel memory: 208k freed
[ 3.860000] ar71xx: pll_reg 0xb8050014: 0x1a000000
[ 3.860000] eth0: link up (1000Mbps/Full duplex)
[ 3.990000] Registered led device: tp-link:green:usb
[ 3.990000] Registered led device: tp-link:green:system
[ 3.990000] Registered led device: tp-link:green:qss
[ 3.990000] Registered led device: tp-link:green:wlan
root@(none):/#

Dev_BR wrote: - QoS Upload:Enabled
- QoS "Normal" Rule Max BW = 700k for Destination: 192.168.2.100

If it is upload, then the source should be your local computer, not the destination - of course it won't work this way.

If it is upload, then the source should be your local computer, not the destination - of course it won't work this way.

You are right,
I was confused cause there was some default rules using ports and destination there.
thanks

Plaese, someone, tell me, what about wr1043nd, how this new firmware works on it?
i am afraid to flash it after last time (problem with password on 1.5.6)....