gargoyle-ispy 2015-October-18 05:57.torrent

Want to share your OpenWrt / Gargoyle knowledge? Implemented a new feature? Let us know here.

Moderator: Moderators

User avatar
djt_nz
Posts: 26
Joined: Mon May 07, 2012 1:00 am
Location: New Zealand

Re: gargoyle-ispy 2015-October-18 05:57.torrent

Postby djt_nz » Sun Nov 08, 2015 10:52 pm

@RichMD The 340 MB file is a zip (7 zip) achieve file of images for all supported routers.
You will need to down load and extract to a temp location then grab the image for your router.

RichMD
Posts: 12
Joined: Sun Oct 27, 2013 11:02 am

Re: gargoyle-ispy 2015-October-18 05:57.torrent

Postby RichMD » Sun Nov 08, 2015 11:42 pm

@djt_nz
Thanks, that makes sense. I just hadn't opened it yet to realize it was for all versions.

RichMD
Posts: 12
Joined: Sun Oct 27, 2013 11:02 am

Re: gargoyle-ispy 2015-October-18 05:57.torrent

Postby RichMD » Mon Nov 09, 2015 12:51 am

I installed 1.9 on my WRT1900AC V1 and with a 1Gb wired connection, speedtest.net showed 175Mb down and 23Mb up which is top speed for my connection. I didn't do anything with the wireless config other than via the GUI and I got 300mb (not full AC) but I got 145Mb down and 23Mb up. I will eventually try to get AC working but this is fine for now. I left the 2.4Ghz radio at 20mhz so I only get 130mb but that is good enough. Everything looks good so far.

nworbnhoj
Posts: 914
Joined: Mon Jul 21, 2014 10:08 am
Location: Australia
Contact:

Re: gargoyle-ispy 2015-October-18 05:57.torrent

Postby nworbnhoj » Mon Nov 09, 2015 1:34 am

RichMD wrote:Everything looks good so far.
These might be of interest next http://www.gargoyle-router.com/wiki/dok ... _scenarios
Can you help someone else get Gargoyle up and running?
TL-WDR3600 : Gargoyle 1.9.0 : NBN FixedWireless
TL-WR1043ND-V2 : Gargoyle 1.8.0 : 3G Huawei E160E

RichMD
Posts: 12
Joined: Sun Oct 27, 2013 11:02 am

Re: gargoyle-ispy 2015-October-18 05:57.torrent

Postby RichMD » Mon Nov 09, 2015 10:20 am

nworbnhoj wrote:
RichMD wrote:Everything looks good so far.
These might be of interest next http://www.gargoyle-router.com/wiki/dok ... _scenarios


Thanks! :D

bill1228
Posts: 12
Joined: Mon Oct 26, 2015 1:28 pm

Re: gargoyle-ispy 2015-October-18 05:57.torrent

Postby bill1228 » Sun Nov 15, 2015 12:45 pm

@RichMD
Another way to switch back to the Linksys partition 1 is the following:

Telnet into the router, if running DD-WRT or Openwrt
Then give this command
ubootenv set boot_part 1
reboot

You can see what partition is the one you are on with this command:
ubootenv get boot_part

This easier then the multiple off/on.
--bill
Linksys WRT3200ACM
Linksys WRT1900ACS V1 standby
Everyone has a right to be stupid once in awhile. Yet some just abuse the privilege.

RichMD
Posts: 12
Joined: Sun Oct 27, 2013 11:02 am

Re: gargoyle-ispy 2015-October-18 05:57.torrent

Postby RichMD » Mon Nov 23, 2015 12:09 am

Thanks Bill,
I saw those commands on the DD-WRT page just now and tried them. I get "ubootenv not found". I am still running the gargoyle firmware though. Is there any equivalent for this version?


Return to “Show / Tell / Contribute”

Who is online

Users browsing this forum: No registered users and 3 guests