Page 1 of 3

Gargoyle-ispy 2013-September-04.7z

Posted: Tue Sep 03, 2013 3:07 pm
by ispyisail
USE AT YOU OWN RISK

Gargoyle-ispy 2013-September-04.7z
http://goo.gl/abW8w3

bump openwrt version

Re: Gargoyle-ispy 2013-September-04.7z

Posted: Wed Sep 04, 2013 5:12 am
by ispyisail
wifi appears to work real well

Re: Gargoyle-ispy 2013-September-04.7z

Posted: Wed Sep 04, 2013 1:10 pm
by azrado

Code: Select all

BusyBox v1.19.4 (2013-09-03 21:29:00 NZST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

------------------------------------------------------------------
|            _____                             _                 |
|           |  __ \                           | |                |
|           | |  \/ __ _ _ __ __ _  ___  _   _| | ___            |
|           | | __ / _` | '__/ _` |/ _ \| | | | |/ _ \           |
|           | |_\ \ (_| | | | (_| | (_) | |_| | |  __/           |
|            \____/\__,_|_|  \__, |\___/ \__, |_|\___|           |
|                             __/ |       __/ |                  |
|                            |___/       |___/                   |
|                                                                |
|----------------------------------------------------------------|
| Gargoyle version 1.5.X    | OpenWrt Attitude Adjustment branch |
| Gargoyle revision 9c5be4b | OpenWrt revision r37174            |
| Built September 03, 2013  | Target  ar71xx/default             |
------------------------------------------------------------------
UPnP working - WR740n v.3

Re: Gargoyle-ispy 2013-September-04.7z

Posted: Thu Sep 05, 2013 7:43 am
by jorgecorazondeleon
wr1043nd v1.8
Dinamycs ip
Everything works goods, except:
Tor not work
Every time I reboot router,Tor menu disappears

Re: Gargoyle-ispy 2013-September-04.7z

Posted: Fri Sep 06, 2013 1:01 am
by florachan
Thanks for posting this. I found D-Link DIR-825 , C1 revision that only supported the OpenWrt Barrier Breaker trunk inside your build. great work. This is not in the download section.

Re: Gargoyle-ispy 2013-September-04.7z

Posted: Fri Sep 06, 2013 12:48 pm
by nuxator
I fond 2 bugs on my wr1043nd :
+Themes or not working anymore (incompatibility?)
+Swap in status is wrong : i have 477 MB swap partition it displays
Swap Memory Usage:0MB / 6677.8MB (0%)
I tried 180MB it displays :
Swap Memory Usage:0MB / 6391.6MB (0%)
Eveything else seems ok.

Re: Gargoyle-ispy 2013-September-04.7z

Posted: Sat Sep 07, 2013 8:28 pm
by pmerrill
Curious. I have loaded this version in hopes of fixing dual channel mode with no luck. For some reason, I cannot get the router to operate in dual channel mode. I've selected Channel 1, 40 MHz, second channel above but I cannot get any wireless connection to work in Wireless N.

InSSider reports that the router is Channel 1 rather than Channel 1+5 for example. However, InSSider can see other routers in the area operating in dual channel mode, just not mine.

It was working in dual channel mode for quite a while but then all of a sudden, just stopped.

Any ideas or thoughts would be greatly appreciated.

Re: Gargoyle-ispy 2013-September-04.7z

Posted: Sat Sep 07, 2013 9:37 pm
by chickennuggets8
pmerrill wrote:Curious. I have loaded this version in hopes of fixing dual channel mode with no luck. For some reason, I cannot get the router to operate in dual channel mode. I've selected Channel 1, 40 MHz, second channel above but I cannot get any wireless connection to work in Wireless N.

InSSider reports that the router is Channel 1 rather than Channel 1+5 for example. However, InSSider can see other routers in the area operating in dual channel mode, just not mine.

It was working in dual channel mode for quite a while but then all of a sudden, just stopped.

Any ideas or thoughts would be greatly appreciated.
Proper and more recent wireless N implementations do not allow for 40mhz mode in the 2.4ghz band if neighboring wifi stations have a strong enough signal. Certain router manufacturers ignore the standard and still allow for 40mhz even though it will cause interference with your neighbor's wifi.

I suspect OpenWRT -- and thereby Gargoyle -- properly implement the dual channel 40mhz checking before allowing 40mhz mode.

Re: Gargoyle-ispy 2013-September-04.7z

Posted: Sun Sep 08, 2013 8:08 am
by buddee
pmerrill wrote:Curious. I have loaded this version in hopes of fixing dual channel mode with no luck. For some reason, I cannot get the router to operate in dual channel mode. I've selected Channel 1, 40 MHz, second channel above but I cannot get any wireless connection to work in Wireless N.

InSSider reports that the router is Channel 1 rather than Channel 1+5 for example. However, InSSider can see other routers in the area operating in dual channel mode, just not mine.

It was working in dual channel mode for quite a while but then all of a sudden, just stopped.

Any ideas or thoughts would be greatly appreciated.
Have you tried selecting some other channel besides an edge channel? Channel 1 and 11, atleast here in the US, are considered edge channels and its harder to get main+aux channel (HT40) working correctly when an edge channel is selected.

Re: Gargoyle-ispy 2013-September-04.7z

Posted: Sun Sep 08, 2013 8:11 am
by buddee
I have finally gotten around to testing this new roll, still having problems with TOR as i described in the previous test build threads. I am wondering why the TOR feature was messed with at all, there was nothing wrong with it in previous builds, now its not working... ah well, hopefully the devs will get it worked out. :)