Page 1 of 3
1.11.0.x gargoyle-ispy 2019-June-23 04
Posted: Tue Jun 25, 2019 12:57 am
by ispyisail
USE AT YOUR OWN RISK
WARNING: DO NOT PRESERVE SETTINGS
Now includes packages
Big changes, its a little bit experimental this one
1.11.0.x gargoyle-ispy 2019-June-23 04
Torrent
http://bit.ly/2RvJEQ4
magnet:?xt=urn:btih:586b2a7af3a7679df0968aacdc48a43d75afb54e&dn=1.11.0.x%20gargoyle-ispy%202019-June-23%2004.7z&tr=udp%3a%2f%2ftracker.openbittorrent.com%3a80&tr=udp%3a%2f%2fopen.demonii.com%3a1337&tr=udp%3a%2f%2ftracker.coppersurfer.tk%3a6969&tr=udp%3a%2f%2ftracker.leechers-paradise.org%3a6969&tr=udp%3a%2f%2ftracker.coppersurfer.tk%3a6969%2fannounce&tr=udp%3a%2f%2ftracker.open-internet.nl%3a6969%2fannounce&tr=udp%3a%2f%2fallesanddro.de%3a1337%2fannounce&tr=udp%3a%2f%2f9.rarbg.to%3a2710%2fannounce
Routers
http://bit.ly/2XyT82r
Changelog
(see creation date for commit date)
https://github.com/ericpaulbishop/gargo ... its/master
Re: 1.11.0.x gargoyle-ispy 2019-June-23 04
Posted: Tue Jun 25, 2019 8:08 am
by Rog66
Thanks ! - upgraded WRT32X (router) and WRT1900ACS (access point)
The 5GHz wouldn't come up on the WRT32X (hostapd failed to start device) until I reset the channel to 36, waited for it to come up and then reset it to 100, then it worked fine - the 5GHz has always seemed buggy on this bit of kit though unless I use a non-DFS channel (not possible if you have a Sky-Q mesh in the house) so don't think its anything to do with this build.
Re: 1.11.0.x gargoyle-ispy 2019-June-23 04
Posted: Tue Jun 25, 2019 9:10 pm
by lceron80
Rog66 wrote:Thanks ! - upgraded WRT32X (router) and WRT1900ACS (access point)
The 5GHz wouldn't come up on the WRT32X (hostapd failed to start device) until I reset the channel to 36, waited for it to come up and then reset it to 100, then it worked fine - the 5GHz has always seemed buggy on this bit of kit though unless I use a non-DFS channel (not possible if you have a Sky-Q mesh in the house) so don't think its anything to do with this build.
thanks for the heads up.
had the same issue in my WRT1900ACV1. this was a similar issue a few releases ago i believe.
another issue i encountered, usually after upgrading the firmware and log in and setup the wifi i get an option to use world wide or US. this time after upgrading i only had the 2 options of world wide and undefined. any thoughts ispyisail?
Re: 1.11.0.x gargoyle-ispy 2019-June-23 04
Posted: Tue Jun 25, 2019 9:37 pm
by Lantis
If you reboot the router the undefined might go away. You can also delete/tmp/cached_basic_vars and refresh the page to achieve the same.
Re: 1.11.0.x gargoyle-ispy 2019-June-23 04
Posted: Wed Jun 26, 2019 1:19 am
by lceron80
another issue i encountered is that the tx power for this beta release is different from before. i remember that before when using the same channels i would be able to use tx power of 30 as default. now it is defaulting to 20.
Re: 1.11.0.x gargoyle-ispy 2019-June-23 04
Posted: Wed Jun 26, 2019 2:55 am
by ispyisail
What is the max power for your country?
https://w.wol.ph/2015/08/28/maximum-wif ... r-country/
Short overview of the ETSI standard:
– 2.4 GHz: 100 mW (20 dBm)
– 5 GHz channel 36 to 64: 200 mW (23 dBm)
– 5 GHz channel 100 to 140: 1000 mW (30 dBm)
– 5 GHz channel 155 to 171: 4000 mW (36 dBm)
Re: 1.11.0.x gargoyle-ispy 2019-June-23 04
Posted: Wed Jun 26, 2019 3:54 am
by lceron80
i'm in the US and i use channel 7 or 11 for 2.4 ghz and should default to 30 db and i use channel 149 or 153 and should deafault to 30 db.
Re: 1.11.0.x gargoyle-ispy 2019-June-23 04
Posted: Wed Jun 26, 2019 4:09 am
by Lantis
20 indicates that your country code is set to the default setting, not the US
Re: 1.11.0.x gargoyle-ispy 2019-June-23 04
Posted: Wed Jun 26, 2019 4:34 am
by tapper
Hi flashed to my wrt1900ac v2 and all is good so far. Thanks. Nice one for the upgrade to OpenWrt 18.06.3
Re: 1.11.0.x gargoyle-ispy 2019-June-23 04
Posted: Wed Jun 26, 2019 11:10 am
by RomanHK
lceron80 wrote:another issue i encountered is that the tx power for this beta release is different from before. i remember that before when using the same channels i would be able to use tx power of 30 as default. now it is defaulting to 20.
lceron80 wrote:i'm in the US and i use channel 7 or 11 for 2.4 ghz and should default to 30 db and i use channel 149 or 153 and should deafault to 30 db.
Here on the forum (
viewtopic.php?f=11&t=11956&p=52795#p52764) has been dealt with many times - the reason is the locked performance of the hardware.
Code: Select all
strings /dev/mtd3|sed -ne 's/^cert_region=//p'