Page 6 of 22

Re: Gargoyle 1.11.0 Release Candidate 5

Posted: Sun Dec 23, 2018 3:58 pm
by lemine
Any chance of 1.11.0 released before Christmas or even New Year?

Re: Gargoyle 1.11.0 Release Candidate 5

Posted: Sun Dec 23, 2018 5:43 pm
by Lantis
I have organised it and asked for it to happen, but haven’t heard back yet unfortunately.
RC5 is a good one to use in the interim

Re: Gargoyle 1.11.0 Release Candidate 5

Posted: Mon Dec 24, 2018 8:39 am
by Wildcats198311
I am very unhappy. I attempted to update my WD MyNet N750. I downloaded the correct file for the router and flashed the update onto the router. It did not complete the install and now the router is in constant boot mode. The power light blinks constantly. I tried doing the recovery option for the router and it does not work. My computer does not recognize the device.
I had a second MyNet N750 and thinking I screwed up the first on my own by flashing a incomplete file, I got the second router and flashed the factory install file to the device. I was able to use the router for a few minutes. I turned WiFi on and then decided I wanted to add my DHCP devices first, I turned off WiFi and now the router is not working. The power light is now constantly blinking on both my devices.


Update...
I was messing around with the routers and some how got them working. I re-flashed RC5 on the one and it seams ok so far. I haven’t tried turning WiFi off and on to see if it glitches the device again.

Re: Gargoyle 1.11.0 Release Candidate 5

Posted: Mon Dec 24, 2018 4:57 pm
by lemine
Tried it on TRENDnet TEW-823DRU, has been up for 16 hours, no problem so far.

Re: Gargoyle 1.11.0 Release Candidate 5

Posted: Tue Dec 25, 2018 12:24 am
by Wildcats198311
I am only having problem if switch WiFi off and on a few times in a row... I know this isn’t a common thing and most will turn it on and leave it on. It just happened that I figured I should do other settings first after I turned it on the first time then had the problem when turned it back off. (I have limited internet, and wanted to set some of my devices up for Quota limit). After I finally got the router to allow me to be re-flashed and had a chance to, I turned WiFi off and on 2-3 times and had the problem again... after that I haven’t turned if off after turning it back on. Had no issues for 9-10 hours or so.

Re: Gargoyle 1.11.0 Release Candidate 5

Posted: Tue Dec 25, 2018 12:52 am
by Lantis
What settings are you using? Wifi and any other optional modules.
It isn’t likely that just turning wifi off and on causes the issue. It will be something else that restarts with the wifi.

Re: Gargoyle 1.11.0 Release Candidate 5

Posted: Tue Dec 25, 2018 9:21 am
by Wildcats198311
I did not do any changes. The first time I had just flashed the firmware onto my brand new MyNet N750 (just took plastic off the box and all) using the factory file. I set a password. Then went to start to set up WiFi, turned it on, and remembered I had to set the quota limits and IP addresses, turned WiFi back off and tried going to To connection to set up stuff there and it went off and the router’s power light started blinking. Could not do anything, powering off the router and even pressing the reset button did nothing. After a few seconds the power light would start blinking.

Re: Gargoyle 1.11.0 Release Candidate 5

Posted: Tue Dec 25, 2018 5:25 pm
by ispyisail
@Wildcats198311

Can you try an older version of gargoyle?

Can you try Openwrt?

Process of elimination

Re: Gargoyle 1.11.0 Release Candidate 5

Posted: Tue Dec 25, 2018 9:51 pm
by Wildcats198311
1.10.x worked great for months. And other previous versions before that, for the last couple years. I never had any problems. 1.11.0 RC5 is working good now as well. I’m not sure what or why the device malfunctioned.

I never tried OpenWRT in the past. I need the Quota feature with throttling. I could never find out for sure if OpenWRT had these features available, so I just stayed with Gargoyle since I knew it worked and had the feature I need the most.

I did put OpenWRT on my old MyNet N750. I did not understand it and didn’t like the layout. I don’t know much about programming and all the add on things. I just want something easy and pretty much basic with the few main features that are already in Gargoyle.
(when I installed the RC5 version the old N750 it went into constant boot mode or something ... I thought I had a incomplete download so I powered off the modem before it completed install which I know I shouldn’t have done... thinking I had bricked the device, I opened my new N750 that I had for a backup. That’s when I had problems with the new device after turning on and off WiFi ).

I have since got both devices in working order. I have Gargoyle 1.11.0 RC 5 on the newer device, and I think I flashed the original WD firmware onto the old one for now but it is not being used.

Re: Gargoyle 1.11.0 Release Candidate 5

Posted: Tue Dec 25, 2018 10:05 pm
by ispyisail
How did you upgrade?

Preserve settings?

Did you try failsafe reset/ re flash without pre
serve settings