Page 1 of 5
[TESTERS WANTED] Gargoyle 1.11.x Bleeding Edge MVEBU
Posted: Sun May 13, 2018 4:59 pm
by Lantis
Latest 1.11.x images + my unmerged patches to increase move to Openwrt 18.06 release branch.
Download here
This build also includes updated patches for the WRT3200ACM handling the new NAND chip, allowing flashing of devices purchased after November 2017.
Additionally, i am pleased to announce that Gargoyle has the
FIRST third party web flashable firmware for the Linksys WRT32X router. See below running full 160MHz channel width in 5GHz.
Re: [TESTERS WANTED] Gargoyle 1.11.x Bleeding Edge MVEBU
Posted: Sun May 13, 2018 6:16 pm
by Rog66
Installed on WRT1900ACS - not sure if it was a general problem (as its late here) or just enabling TOR (which it seemed to coincide with) - lost DNS/WAN connection and had to reboot into second partition - disabling TOR didn't fix the issue and neither did a factory reset. Will try again when I can and report back
Re: [TESTERS WANTED] Gargoyle 1.11.x Bleeding Edge MVEBU
Posted: Sun May 13, 2018 6:24 pm
by Lantis
I haven’t tested TOR at all, I wouldn’t be overly surprised.
If you can confirm that is what caused your issue I can look at it, but I’ve never used TOR so I wouldn’t know where to begin.
Re: [TESTERS WANTED] Gargoyle 1.11.x Bleeding Edge MVEBU
Posted: Mon May 14, 2018 6:57 am
by phgerin
Installed on WRT1200, upgraded from LEDE.
I can't get any dynamic network service to work.
Everything else is ok for now.
Thanks for the build !
Re: [TESTERS WANTED] Gargoyle 1.11.x Bleeding Edge MVEBU
Posted: Mon May 14, 2018 7:18 am
by phgerin
Does anyone know how to install snmpd ?
Tried
http://downloads.lede-project.org/snaps ... /packages/
snmpd does install but crashes.
Re: [TESTERS WANTED] Gargoyle 1.11.x Bleeding Edge MVEBU
Posted: Mon May 14, 2018 8:23 am
by Lantis
Which DDNS? Weren't you having trouble with that before this build?
Re: [TESTERS WANTED] Gargoyle 1.11.x Bleeding Edge MVEBU
Posted: Mon May 14, 2018 9:36 am
by phgerin
Didn't test with previous builds.
I have tried noip.com and dyndns. It just don't update and the force option does nothing.
Mon May 14 14:02:07 2018 daemon.info ddns_gargoyle[4223]: Successfully retrieved local ip from url:
http://www.tracemyip.org
Mon May 14 14:02:07 2018 daemon.info ddns_gargoyle[4223]: local IP = 109.129.yyy.xxx
Mon May 14 14:02:07 2018 daemon.info ddns_gargoyle[4223]: remote IP cannot be determined
Re: [TESTERS WANTED] Gargoyle 1.11.x Bleeding Edge MVEBU
Posted: Mon May 14, 2018 6:34 pm
by Lantis
I’ll check those two services, but it worked fine for me on cloudflare
Re: [TESTERS WANTED] Gargoyle 1.11.x Bleeding Edge MVEBU
Posted: Tue May 15, 2018 1:08 am
by Cloudyytechie
Just installed onto my wrt3200acm it’s working very well no bugs so far the Wi-Fi driver is also amazing
Re: [TESTERS WANTED] Gargoyle 1.11.x Bleeding Edge MVEBU
Posted: Tue May 15, 2018 2:43 am
by phgerin
Tried to revert to stock firmware and then back to Gargoyle.
Adding a new ddns service never ends.
The config looks ok (/etc/ddns_gargoyle.conf) , but it never update.
The force update option never ends.
dyndns / changeip / no-ip