Gargoyle Forum

Hi All,

Working fine on Archer C7 V2, but QoS distribution graph shows only 1/4 of the pie, I'm using IE. not a big issue, but everything looks fine.

Thank you all for all your hard work.

coits wrote:Hi All,

Working fine on Archer C7 V2, but QoS distribution graph shows only 1/4 of the pie, I'm using IE. not a big issue, but everything looks fine.

Thank you all for all your hard work.

Please clear your browser cache.
These are BIG updates with lots of UI changes that are non trivial.

viewtopic.php?f=14&t=10723&start=10#p43543

I've only got one problem that's been there for the last 4 or 5 releases and that is the QoS (Download) - Active Congestion Control not displaying the status.

On a recommendation I did a firstboot -y to reset from scratch but it did not work. This is what I can see.

https://1drv.ms/i/s!AmhBeIynajxqkFEFy1LNrcuDY29n

Is the qosmon task running?

Lantis wrote:Is the qosmon task running?

I assume I check by telnet into router and doing a ps?

If so, the answer is no, I can't see qosmon running.
root@Gargoyle:/etc/rc.d# ps
PID USER VSZ STAT COMMAND
1 root 1412 S /sbin/procd
2 root 0 SW [kthreadd]
3 root 0 SW [ksoftirqd/0]
4 root 0 SW [kworker/0:0]
5 root 0 SW< [kworker/0:0H]
6 root 0 SW [kworker/u2:0]
7 root 0 SW< [khelper]
33 root 0 SW< [writeback]
66 root 0 SW< [bioset]
69 root 0 SW< [kblockd]
71 root 0 SW [kworker/0:1]
72 root 0 SW [kswapd0]
73 root 0 SW [fsnotify_mark]
75 root 0 SW [spi0]
288 root 0 SW< [deferwq]
289 root 0 SW [kworker/u2:2]
408 root 0 SWN [jffs2_gcd_mtd3]
467 root 892 S /sbin/ubusd
476 root 772 S /sbin/askfirst /bin/ash --login
809 root 0 SW< [rpciod]
820 root 0 SW< [nfsiod]
869 root 0 SW< [cfg80211]
875 root 0 SW< [ath10k_wq]
876 root 0 SW< [ath10k_aux_wq]
1458 root 1044 S /sbin/logd -S 16
1476 nobody 1028 S /usr/sbin/portmap
1495 root 1568 S /sbin/netifd
1558 root 1368 S /usr/sbin/ntpd -n -l -S /usr/sbin/ntpd-hotplug -p 0.oceania.pool.ntp.org -p 1.oceania.pool.ntp.org -p 2.oceania.pool.ntp.org
1600 root 1152 S /usr/sbin/dropbear -F -P /var/run/dropbear.1.pid -p 22 -K 300
1654 root 1960 S /usr/sbin/uhttpd -f -h /www -r Gargoyle -x /cgi-bin -t 900 -T 30 -k 20 -A 1 -E /login.sh -n 50 -N 200 -D -R -p 0.0.0.0:80 -i .sh=/usr/bin/run_haserl -i .csv=/usr/bin/run_haserl -I login.sh -C /etc/uhttpd.crt -
1830 root 1364 S udhcpc -p /var/run/udhcpc-eth0.pid -s /lib/netifd/dhcp.script -f -t 0 -i eth0 -C
2126 root 1548 S /usr/bin/ddns_gargoyle -P /etc/ddns_providers.conf -C /etc/ddns_gargoyle.conf -d
2298 root 1860 S /usr/sbin/hostapd -P /var/run/wifi-phy1.pid -B /var/run/hostapd-phy1.conf
2343 root 1848 S /usr/sbin/hostapd -P /var/run/wifi-phy0.pid -B /var/run/hostapd-phy0.conf
2675 nobody 948 S /usr/sbin/dnsmasq -C /var/etc/dnsmasq.conf -k -x /var/run/dnsmasq/dnsmasq.pid
2806 root 1156 S /usr/sbin/miniupnpd -f /var/etc/miniupnpd.conf
7623 root 1220 R /usr/sbin/dropbear -F -P /var/run/dropbear.1.pid -p 22 -K 300
7716 root 1368 S -ash
13355 root 1368 S /usr/sbin/crond -f -c /etc/crontabs -l 9
14632 root 1364 R ps
root@Gargoyle:/etc/rc.d#

Ssh not telnet, then yes PS

Just a followup. I've rebooted a few times now and qosmon never gets started. It's been that way for a number of releases as well, I assume, because I've had this defect for a number of releases. Perhaps something to do with the Archer C7 V2 specifically?

I've connected the router to my syslog server and there are a number of errors in there as well but nothing with the word qos in them.

Ideas?

It should get started by the main QoS init script.
What if you disable and reenable

You're the only person reporting this problem.

Lantis wrote:It should get started by the main QoS init script.
What if you disable and reenable

You're the only person reporting this problem.

disable/re-enable no effect

While no one else has reported it, I have it, no doubt there.

I see that qosmon is in /usr/sbin/qosmon and /etc/init.d has qos_gargoyle, any reason why I cannot run from an ssh session with the right parameters?

Ok, from /etc/init.d I did a
./qos_gargoyle stop
./qos_gargoyle start

I got 4 errors in syslog but no qosmon started.

The errors were:
daemon insmod module is already loaded - sch_sfq
daemon insmod module is already loaded - sch_hfsc
daemon insmod module is already loaded - cls_flow
daemon insmod module is already loaded - cls_fw