Search found 1373 matches
- Fri May 30, 2014 2:24 am
- Forum: Hardware / Installation Issues
- Topic: v 2.0 TL-WR1043ND with Atheros AR83xx
- Replies: 8
- Views: 19651
Re: v 2.0 TL-WR1043ND with Atheros AR83xx
http://wiki.openwrt.org/toh/tp-link/tl-wr1043nd View that page for info on WR1043ND-V2 Gargoyle runs on OpenWRT underneath so any hardware questions should be researched on the OpenWRT website/forums/wiki If there is a image available for download - it should flash BUT - as always - you take the ris...
- Fri May 30, 2014 2:21 am
- Forum: Hardware / Installation Issues
- Topic: TL-WR841ND - Flashed ok but..
- Replies: 5
- Views: 6113
Re: TL-WR841ND - Flashed ok but..
1) Reset to defaults
2) Re-flash 1.6.1
3) Try a different browser (make sure the cache is cleared)
Try the above
2) Re-flash 1.6.1
3) Try a different browser (make sure the cache is cleared)
Try the above
- Fri May 30, 2014 2:17 am
- Forum: General Discussion
- Topic: Rosewill 300RT Would I be able to go back Stock
- Replies: 1
- Views: 1903
Re: Rosewill 300RT Would I be able to go back Stock
You should be able to flash back and forth from Gargoyle to DD-WRT
Make sure you are able to serial recover if it's that critical to you
There's always a chance for a bad flash and you might have to
serial recover a router.
Make sure you are able to serial recover if it's that critical to you
There's always a chance for a bad flash and you might have to
serial recover a router.
- Sun May 25, 2014 11:39 pm
- Forum: Hardware / Installation Issues
- Topic: help
- Replies: 7
- Views: 5955
Re: help
Could be a corrupted config
Try the steps listed here:
http://www.gargoyle-router.com/phpbb/vi ... f=8&t=2080
You will probably have to re-configure fresh
If you can get back in - don't load an old config - reconfigure fresh!
Try the steps listed here:
http://www.gargoyle-router.com/phpbb/vi ... f=8&t=2080
You will probably have to re-configure fresh
If you can get back in - don't load an old config - reconfigure fresh!
- Sun May 25, 2014 11:37 pm
- Forum: Monitoring / Quota / QoS Issues
- Topic: Incorrect Date
- Replies: 7
- Views: 7454
Re: Incorrect Date
Backup your current config
Reset to defaults and see if you can get the time/date to sync properly
If you can, then reload your old config
If the time/date goes wacky again - you have a corrupted config
and you have to again - reset to defaults, then reconfigure fresh
Reset to defaults and see if you can get the time/date to sync properly
If you can, then reload your old config
If the time/date goes wacky again - you have a corrupted config
and you have to again - reset to defaults, then reconfigure fresh
- Fri May 23, 2014 12:11 pm
- Forum: General Discussion
- Topic: help
- Replies: 1
- Views: 1711
Re: help
If you have a WRT54G model, try the 1.4.7 firmware first
See how that works first.
See how that works first.
- Thu May 22, 2014 10:59 pm
- Forum: General Discussion
- Topic: Does This Firmware Work With Neatgear's R6100?
- Replies: 2
- Views: 2722
Re: Does This Firmware Work With Neatgear's R6100?
Not right now
Has to be supported by OpenWRT first before it could get
support for Gargoyle.
Looks like you might have some luck with DD-WRT soon
Also check for Tomato Firmware - that may support it soon too
Has to be supported by OpenWRT first before it could get
support for Gargoyle.
Looks like you might have some luck with DD-WRT soon
Also check for Tomato Firmware - that may support it soon too
- Thu May 22, 2014 1:10 pm
- Forum: Network / Wireless Issues
- Topic: Network Setup Advice/Help: Wireless modem to Gargoyle wired
- Replies: 4
- Views: 5705
Re: Network Setup Advice/Help: Wireless modem to Gargoyle wi
Save yourself a LOT of hassle and get one of these: http://www.dlink.com/us/en/home-solutions/connect/powerline You can then connect the NDR3700 WAN port up over wire and not have to worry about a wireless bridge setup You can find them on sale all the time I run multiple wireless bridges in my hous...
- Thu May 22, 2014 11:36 am
- Forum: General Discussion
- Topic: Is it ok to flash WR941 V3.8 with this firmware
- Replies: 2
- Views: 2524
Re: Is it ok to flash WR941 V3.8 with this firmware
See this page
http://wiki.openwrt.org/toh/tp-link/tl-wr941nd
Should be fine to flash Gargoyle 1.6.0 or 1.6.1
DO NOT FLASH ANYTHING BELOW 1.5.7 on your WR941 V3.8
You need Attitude Adjustment branch for your V3.8
Versions you could try:
1.5.10
1.5.11
1.6.0
1.6.1
http://wiki.openwrt.org/toh/tp-link/tl-wr941nd
Should be fine to flash Gargoyle 1.6.0 or 1.6.1
DO NOT FLASH ANYTHING BELOW 1.5.7 on your WR941 V3.8
You need Attitude Adjustment branch for your V3.8
Versions you could try:
1.5.10
1.5.11
1.6.0
1.6.1
- Wed May 21, 2014 1:12 am
- Forum: Hardware / Installation Issues
- Topic: Transmit Custom Power Issue
- Replies: 1
- Views: 3272
Re: Transmit Custom Power Issue
I just finished upgrading router number 3 TP-Link TL-WR1043N/ND v1 to Gargoyle Version:1.6.1 when I attempt to set the custom transmit power (I don't think my neighbors 2 miles away need to see my signal :lol: ) to something other than 27 it keeps at custom 27 any ideas works fine on version 2 Than...