Search found 6735 matches

by Lantis
Tue Mar 26, 2024 5:47 am
Forum: Show / Tell / Contribute
Topic: Gargoyle 1.15.x BETA - 2024-03-11 - Based on OpenWrt 23.05
Replies: 26
Views: 1837

Re: Gargoyle 1.15.x BETA - 2024-03-11 - Based on OpenWrt 23.05

The usteer package is installed by default on most profiles, others will need to install it. There is no GUI configuration for usteer except for being able to turn it on and off to help send AP client information between multiple Gargoyle routers on the same network (in a multi-AP setup for example)...
by Lantis
Mon Mar 25, 2024 5:28 pm
Forum: Network / Wireless Issues
Topic: Flint 2 IPv6 Help?
Replies: 23
Views: 869

Re: Flint 2 IPv6 Help?

If I can’t figure it out though you may need to either accept it or try to investigate it yourself. Moderate NAT is perfectly fine for playing games anyway :)
by Lantis
Mon Mar 25, 2024 8:22 am
Forum: Network / Wireless Issues
Topic: Flint 2 IPv6 Help?
Replies: 23
Views: 869

Re: Flint 2 IPv6 Help?

Doesn't make much sense, as packet-too-big is allowed through the firewall by default (you can see it in /etc/config/firewall).

I'll flash their firmware again on the weekend and see if I can see anything else obvious.
by Lantis
Mon Mar 25, 2024 8:19 am
Forum: General Discussion
Topic: wich new router? (coming from a archer c7
Replies: 2
Views: 57

Re: wich new router? (coming from a archer c7

WRT3200ACM is supported in 1.15 beta (available in the Show and Tell part of the forum). Yes it will have wifi issues.

viewtopic.php?t=17920
Recent thread with a similar question.
by Lantis
Mon Mar 25, 2024 7:04 am
Forum: Network / Wireless Issues
Topic: Flint 2 IPv6 Help?
Replies: 23
Views: 869

Re: Flint 2 IPv6 Help?

I checked IPv6 pinhole support through UPnP and it worked fine (but didn’t show on the GUI).
So it shouldn’t be an issue there.
by Lantis
Sun Mar 24, 2024 7:25 pm
Forum: Network / Wireless Issues
Topic: Flint 2 IPv6 Help?
Replies: 23
Views: 869

Re: Flint 2 IPv6 Help?

No you don’t need to port forward ipv6 (unless you’re using NAT6), but you do need to open ports to devices.
I’m not confident this is handled by UPnP in Gargoyle
by Lantis
Sat Mar 23, 2024 11:55 pm
Forum: Network / Wireless Issues
Topic: Flint 2 IPv6 Help?
Replies: 23
Views: 869

Re: Flint 2 IPv6 Help?

Well that’s good news! I’ll do some work to add these extra config items into the GUI in the future. I’ll try to find some time to check if they do anything different as far as UPnP in the OEM firmware. From what I can gather, Xbox requires the following ports opened: TCP: 3074 UDP: 88, 500, 3074, 3...
by Lantis
Sat Mar 23, 2024 8:39 am
Forum: Network / Wireless Issues
Topic: Flint 2 IPv6 Help?
Replies: 23
Views: 869

Re: Flint 2 IPv6 Help?

I flashed the stock firmware and compared what gl-inet change when you set "passthrough" mode on IPv6. Here's a comparison: https://www.diffchecker.com/E9LuxVT1/ In /etc/config/dhcp they set config dhcp 'lan' ... option dhcpv6 'relay' option ra 'relay' option ndp 'relay' The only bit you a...
by Lantis
Sat Mar 23, 2024 2:06 am
Forum: Network / Wireless Issues
Topic: Flint 2 IPv6 Help?
Replies: 23
Views: 869

Re: Flint 2 IPv6 Help?

Yes that's right. However, I've not used FireFox in ages and it's different enough that the instructions won't make much sense how I describe them. Lets change methods. Login with WinSCP (if you've not used that before, see here https://www.gargoyle-router.com/phpbb/viewtopic.php?t=8505) Navigate to...
by Lantis
Fri Mar 22, 2024 7:50 pm
Forum: Network / Wireless Issues
Topic: Flint 2 IPv6 Help?
Replies: 23
Views: 869

Re: Flint 2 IPv6 Help?

Ahh, so you’re not getting any prefix delegation. This is one of the few cases where you might need to set some options I disabled. You need to set dhcpv6 and router advertisements to “relayed” on the DHCP page. You can do this via the command line or in the browser by removing the “disabled” flag f...