Search found 58 matches

by lollapalooza
Thu Jan 10, 2019 12:47 pm
Forum: General Discussion
Topic: WPA2 Enterprise support (wireless gateway)
Replies: 4
Views: 474

Re: WPA2 Enterprise support (wireless gateway)

Ok, I found the solution. At the end I had to install OpenWRT, remove wpad-mini and install wpad. Then I created the configuration via OpenWRT web interface, and went to check the file /etc/config/wireless Then I reinstalled Gargoyle, and copied the same parameters in the same file. In my case corr...
by lollapalooza
Thu Jan 10, 2019 12:46 pm
Forum: General Discussion
Topic: WPA2 Enterprise support (wireless gateway)
Replies: 4
Views: 474

Re: WPA2 Enterprise support (wireless gateway)

Ok, I found the solution. At the end I had to install OpenWRT, remove wpad-mini and install wpad. Then I created the configuration via OpenWRT web interface, and went to check the file /etc/config/wireless Then I reinstalled Gargoyle, and copied the same parameters in the same file. In my case corre...
by lollapalooza
Thu Jan 10, 2019 12:46 pm
Forum: Other Issues
Topic: BUG: OpenVPN config is not being backed up.
Replies: 1
Views: 303

BUG: OpenVPN config is not being backed up.

I had to uninstall and reinstall Gargoyle to make a few tests with OpenWRT. Obviously I did a backup of the config via Gargoyle WebGUI, so it should have been easy to restore once reinstalled. Unfortunately all configurations were backed up, except OpenVPN config (I had it configured as a client). N...
by lollapalooza
Tue Jan 08, 2019 3:43 pm
Forum: General Discussion
Topic: WPA2 Enterprise support (wireless gateway)
Replies: 4
Views: 474

Re: WPA2 Enterprise support (wireless gateway)

I tried, but could not manage :-(
by lollapalooza
Sun Jan 06, 2019 7:36 am
Forum: General Discussion
Topic: WPA2 Enterprise support (wireless gateway)
Replies: 4
Views: 474

WPA2 Enterprise support (wireless gateway)

I need to use Gargoyle 1.10 as a wireless gateway, and the network that I need to connect to is using:
802.1x EAP
PEAP
MSCHAPv2

There's no way to configure this via web GUI ...
Can I set up this via SSH?

Can somebody help?
by lollapalooza
Wed Nov 07, 2018 5:04 am
Forum: Other Issues
Topic: Wireless Bridge/Repeater mode
Replies: 7
Views: 536

Re: Wireless Bridge/Repeater mode

I have tried many times to unplug/plug the RJ45 cable, and also to run ipconfig /release and ipconfig /renew command.

Wired client takes an IP on the same subnet as the main router (192.168.1.0/24).
by lollapalooza
Tue Nov 06, 2018 5:06 pm
Forum: Other Issues
Topic: Wireless Bridge/Repeater mode
Replies: 7
Views: 536

Re: Wireless Bridge/Repeater mode

I think both of these IPs are displayed on the Overview screen once it is up and running. You are right, they are shown... Anyway I tried what you say, but it does not work. Screenshot below are the settings: https://i.postimg.cc/PphK1kFM/Cattura.jpg Main router IP is 192.168.1.254/24 Bridge IP is ...
by lollapalooza
Mon Nov 05, 2018 8:02 pm
Forum: Other Issues
Topic: Wireless Bridge/Repeater mode
Replies: 7
Views: 536

Re: Wireless Bridge/Repeater mode

I’ll give it a try tomorrow... thank you.
by lollapalooza
Mon Nov 05, 2018 6:11 pm
Forum: Other Issues
Topic: Wireless Bridge/Repeater mode
Replies: 7
Views: 536

Re: Wireless Bridge/Repeater mode

Yes, I saw that. But (honestly) I tough it was a mistake :-D Now the question is: if I give Gargoyle an IP on a different subnet, how do I open the Gargoyle Web UI (or SSH) afterwards? I.e. main router and clients will be on 192.168.1.0/24, while Gargoyle will be 192.168.2.0/24... and it will be alo...
by lollapalooza
Mon Nov 05, 2018 4:18 pm
Forum: Other Issues
Topic: Wireless Bridge/Repeater mode
Replies: 7
Views: 536

Wireless Bridge/Repeater mode

I'm trying to set-up Gargoyle (1.10.0) as a Wireless Bridge. Basically I need it to be connected to a Wi-Fi network, and to provide internet connectivity on LAN ports (no Wi-Fi access). In short: Main router -> (Wi-Fi) -> Gargoyle -> (wired) -> Clients I have set up the Wireless Bridge/Repeater mode...

Go to advanced search