Search found 6 matches

by ccy
Thu Feb 02, 2017 9:39 pm
Forum: General Discussion
Topic: ARCHER C2 AC750 4-port Gigabit Dual Band
Replies: 4
Views: 12259

Re: ARCHER C2 AC750 4-port Gigabit Dual Band

ARCHER C2 AC750 4-port Gigabit Dual Band isn't supported by Gargoyle Router to date. However, there is a openwrt firmware built by yoq that works with Archer C2 AC750. Follow this links: https://forum.openwrt.org/viewtopic.php?id=52625&p=5 I have tried it myself and it works. It also has instruc...
by ccy
Wed Sep 30, 2015 4:58 am
Forum: Hardware / Installation Issues
Topic: TP-Link 1043ND v1 bricked after upgrade to 1.8.0
Replies: 3
Views: 3474

Re: TP-Link 1043ND v1 bricked after upgrade to 1.8.0

After following the instruction to 1. open TP Link 1043ND casing 2. Solder a 4 pins connector to VCC, GND, RX and TX 3. Plug the USB to Serial cable to pin GND, RX and TX only 4. Use Putty to open the COM3 (in my case) with (115200, N, 8, 1) 5. Power up TP Link 1043ND and can notice blinks on all LE...
by ccy
Tue Sep 29, 2015 7:00 pm
Forum: Hardware / Installation Issues
Topic: TP-Link 1043ND v1 bricked after upgrade to 1.8.0
Replies: 3
Views: 3474

TP-Link 1043ND v1 bricked after upgrade to 1.8.0

I have a TP-Link 1043ND v1 wifi router using Gargoyle since 1.5.0 to 1.7.1. All the while I flash the firmware is fine. Until yesterday, I flash from 1.7.1 to 1.8.0 stable, I realise that my router has bricked. The SYS led has no response for long time. I switch off and on the router again and SYS l...
by ccy
Sat Nov 12, 2011 11:50 pm
Forum: General Discussion
Topic: Can Router IP request from DHCP server?
Replies: 4
Views: 3890

Re: Can Router IP request from DHCP server?

Thanks. Perhaps I didn't ask clearly about my intention. I want to make the router as normal DHCP client on my LAN. It seems like the Gargoyle Web UI doesn't have any option to make the device as DHCP client. At the moment, I must enter a static IP address to the device.
by ccy
Sat Nov 12, 2011 3:45 am
Forum: General Discussion
Topic: Can Router IP request from DHCP server?
Replies: 4
Views: 3890

Can Router IP request from DHCP server?

I have successfully setup Gargarle WRT on TP-LINK TL-WR1043ND wifi router. In Gargorle Connection | Basic page, there is a section "Local Network / LAN" to setup router's IP. The IP has to be enter statically. In some situation, I want to use the router as normal DHCP client on my LAN that...
by ccy
Tue Jul 26, 2011 9:44 am
Forum: General Discussion
Topic: Safe installation on TP-Link TL-WR741ND version 2.4
Replies: 6
Views: 24597

Safe installation on TP-Link TL-WR741ND version 2.4

I have a TL-WR741ND version 2.4 wifi router. Gargoyle firmware on TL-WR741ND version 2.4 seems not fully tested yet. I am looking for a safe way to deploy openwrt / Gargoyle on this router. I don't want to brick the router while install. Is there a safe way to perform the installation that may rollb...