I have WRT1900AC V2 which is similar to ACS, anyway, I have no problem with 5Ghz, my Nexus Player is connected via 5Ghz. I input all my settings again instead of loading a backup config file from 1.9.1 and waited about 5 minutes before inputting settings. Hope this help.bake15 wrote:My 5ghz has disappeared a couple of times in the last 24 hours or so. The ssid is also grayed out but currently working.kanenas wrote:It seems that 5ghz wifi is not working and it is always gray,I tried to turn off 2.4ghz, turn on, reboot, use different channel widths, use the same ssid name, other channels, custom transmit power and etc... every time the 5ghz ssid is graykanenas wrote:Installed for almost 24hours on mt7620 (xiaomi) and seems everything is working fine!
Thank you!
(using the 1.9.2 release no problem)
Please help
I'm using a WRT1900ACS.
Version 1.10.0 : New stable version with critical security fixes
Moderator: Moderators
Re: Version 1.10.0 : New stable version with critical security fixes
Re: Version 1.10.0 : New stable version with critical security fixes
Please chech the screenshot with my settingsLantis wrote:so can you please provide additional details? a copy of your settings?
You're only noticing it because the 2.4GHz one is returning Black
https://imgur.com/a/ZTrIk
Re: Version 1.10.0 : New stable version with critical security fixes
Can you please provide a “dmesg” and “logread” 30 seconds after issuing a “wifi” command at the command line?
https://lantisproject.com/downloads/gargoylebuilds for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.
Please be respectful when posting. I do this in my free time on a volunteer basis.
Re: Version 1.10.0 : New stable version with critical security fixes
Upgraded my WNDR3800 yesterday and seems to be working well. Didn't encounter the 5 GHz issues reported above, and it's what my main box connects via (looking more closely, the SSID setting is slightly greyed - so subtly that I didn't even notice previously).
Settings were done from scratch; didn't preserve or restore from backup.
Settings were done from scratch; didn't preserve or restore from backup.
Netgear WNDR3800
Re: Version 1.10.0 : New stable version with critical security fixes
Please provide more info, I just ssh to it and used the command wifi enable and then dmesgLantis wrote:Can you please provide a “dmesg” and “logread” 30 seconds after issuing a “wifi” command at the command line?
Code: Select all
[13660.020000] device wlan1 entered promiscuous mode
[13660.020000] br-lan: port 2(wlan1) entered forwarding state
[13660.030000] br-lan: port 2(wlan1) entered forwarding state
[13660.880000] br-lan: port 2(wlan1) entered disabled state
[13661.620000] br-lan: port 2(wlan1) entered forwarding state
[13661.620000] br-lan: port 2(wlan1) entered forwarding state
[13663.620000] br-lan: port 2(wlan1) entered forwarding state
[13682.730000] device wlan1 left promiscuous mode
[13682.730000] br-lan: port 2(wlan1) entered disabled state
[13683.800000] device wlan0 entered promiscuous mode
[13683.810000] device wlan0 left promiscuous mode
[13683.810000] br-lan: port 2(wlan0) entered disabled state
[13683.920000] device wlan1 entered promiscuous mode
[13683.920000] br-lan: port 2(wlan1) entered forwarding state
[13683.930000] br-lan: port 2(wlan1) entered forwarding state
[13684.770000] br-lan: port 2(wlan1) entered disabled state
[13685.520000] br-lan: port 2(wlan1) entered forwarding state
[13685.520000] br-lan: port 2(wlan1) entered forwarding state
[13687.520000] br-lan: port 2(wlan1) entered forwarding state
[13819.910000] device wlan1 left promiscuous mode
[13819.910000] br-lan: port 2(wlan1) entered disabled state
[13820.980000] device wlan0 entered promiscuous mode
[13820.990000] device wlan0 left promiscuous mode
[13820.990000] br-lan: port 2(wlan0) entered disabled state
[13821.090000] device wlan1 entered promiscuous mode
[13821.090000] br-lan: port 2(wlan1) entered forwarding state
[13821.100000] br-lan: port 2(wlan1) entered forwarding state
[13821.950000] br-lan: port 2(wlan1) entered disabled state
Code: Select all
Tue Oct 31 23:56:34 2017 daemon.notice netifd: Network device 'wlan1' link is down
Tue Oct 31 23:56:34 2017 daemon.notice netifd: radio1 (29707): command failed: Operation not supported (-122)
Tue Oct 31 23:56:34 2017 daemon.notice netifd: radio0 (29671): Configuration file: /var/run/hostapd-phy0.conf
Tue Oct 31 23:56:35 2017 daemon.notice netifd: radio1 (29707): Configuration file: /var/run/hostapd-phy1.conf
Tue Oct 31 23:56:35 2017 daemon.notice netifd: radio0 (29671): wlan0: IEEE 802.11 Configured channel (52) not found from the channel list of current mode (2) IEEE 802.11a
Tue Oct 31 23:56:35 2017 kern.info kernel: [13653.520000] device wlan0 entered promiscuous mode
Tue Oct 31 23:56:35 2017 daemon.warn hostapd: wlan0: IEEE 802.11 Configured channel (52) not found from the channel list of current mode (2) IEEE 802.11a
Tue Oct 31 23:56:35 2017 daemon.notice netifd: radio0 (29671): wlan0: IEEE 802.11 Hardware does not support configured channel
Tue Oct 31 23:56:35 2017 daemon.warn hostapd: wlan0: IEEE 802.11 Hardware does not support configured channel
Tue Oct 31 23:56:35 2017 daemon.notice netifd: radio0 (29671): Could not select hw_mode and channel. (-3)
Tue Oct 31 23:56:35 2017 daemon.notice netifd: radio0 (29671): wlan0: interface state UNINITIALIZED->DISABLED
Tue Oct 31 23:56:35 2017 daemon.notice netifd: radio0 (29671): wlan0: AP-DISABLED
Tue Oct 31 23:56:35 2017 daemon.notice netifd: radio0 (29671): wlan0: Unable to setup interface.
Tue Oct 31 23:56:35 2017 daemon.notice netifd: radio0 (29671): wlan0: interface state DISABLED->DISABLED
Tue Oct 31 23:56:35 2017 daemon.notice netifd: radio0 (29671): wlan0: AP-DISABLED
Tue Oct 31 23:56:35 2017 daemon.notice netifd: radio0 (29671): hostapd_free_hapd_data: Interface wlan0 wasn't started
Tue Oct 31 23:56:35 2017 daemon.notice netifd: radio0 (29671): nl80211: deinit ifname=wlan0 disabled_11b_rates=0
Tue Oct 31 23:56:35 2017 kern.info kernel: [13653.600000] device wlan0 left promiscuous mode
Tue Oct 31 23:56:35 2017 kern.info kernel: [13653.610000] br-lan: port 2(wlan0) entered disabled state
Tue Oct 31 23:56:35 2017 daemon.notice netifd: radio0 (29671): cat: can't open '/var/run/wifi-phy0.pid': No such file or directory
Tue Oct 31 23:56:35 2017 kern.info kernel: [13653.630000] device wlan1 entered promiscuous mode
Tue Oct 31 23:56:35 2017 kern.info kernel: [13653.630000] br-lan: port 2(wlan1) entered forwarding state
Tue Oct 31 23:56:35 2017 kern.info kernel: [13653.640000] br-lan: port 2(wlan1) entered forwarding state
Tue Oct 31 23:56:35 2017 daemon.notice netifd: radio1 (29707): wlan1: interface state UNINITIALIZED->HT_SCAN
Tue Oct 31 23:56:35 2017 daemon.notice netifd: radio0 (29671): Command failed: Invalid argument
Tue Oct 31 23:56:35 2017 daemon.notice netifd: radio0 (29671): Device setup failed: HOSTAPD_START_FAILED
Tue Oct 31 23:56:36 2017 kern.info kernel: [13654.490000] br-lan: port 2(wlan1) entered disabled state
Tue Oct 31 23:56:36 2017 daemon.notice netifd: radio1 (29707): 20/40 MHz operation not permitted on channel pri=11 sec=7 based on overlapping BSSes
Tue Oct 31 23:56:36 2017 daemon.notice netifd: radio1 (29707): Using interface wlan1 with hwaddr f0:b4:29:58:bb:f0 and ssid "asdfghjkl"
Tue Oct 31 23:56:36 2017 kern.info kernel: [13655.230000] br-lan: port 2(wlan1) entered forwarding state
Tue Oct 31 23:56:36 2017 kern.info kernel: [13655.230000] br-lan: port 2(wlan1) entered forwarding state
Tue Oct 31 23:56:36 2017 daemon.notice netifd: radio1 (29707): wlan1: interface state HT_SCAN->ENABLED
Tue Oct 31 23:56:36 2017 daemon.notice netifd: radio1 (29707): wlan1: AP-ENABLED
Tue Oct 31 23:56:36 2017 daemon.notice netifd: Network device 'wlan1' link is up
Tue Oct 31 23:56:38 2017 kern.info kernel: [13657.230000] br-lan: port 2(wlan1) entered forwarding state
Tue Oct 31 23:56:40 2017 kern.info kernel: [13658.850000] device wlan1 left promiscuous mode
Tue Oct 31 23:56:40 2017 kern.info kernel: [13658.850000] br-lan: port 2(wlan1) entered disabled state
Tue Oct 31 23:56:40 2017 daemon.notice netifd: Network device 'wlan1' link is down
Tue Oct 31 23:56:40 2017 daemon.notice netifd: radio1 (29982): command failed: Operation not supported (-122)
Tue Oct 31 23:56:41 2017 daemon.notice netifd: radio0 (29941): Configuration file: /var/run/hostapd-phy0.conf
Tue Oct 31 23:56:41 2017 daemon.warn hostapd: wlan0: IEEE 802.11 Configured channel (52) not found from the channel list of current mode (2) IEEE 802.11a
Tue Oct 31 23:56:41 2017 daemon.warn hostapd: wlan0: IEEE 802.11 Hardware does not support configured channel
Tue Oct 31 23:56:41 2017 daemon.notice netifd: radio0 (29941): wlan0: IEEE 802.11 Configured channel (52) not found from the channel list of current mode (2) IEEE 802.11a
Tue Oct 31 23:56:41 2017 daemon.notice netifd: radio0 (29941): wlan0: IEEE 802.11 Hardware does not support configured channel
Tue Oct 31 23:56:41 2017 daemon.notice netifd: radio0 (29941): Could not select hw_mode and channel. (-3)
Tue Oct 31 23:56:41 2017 daemon.notice netifd: radio0 (29941): wlan0: interface state UNINITIALIZED->DISABLED
Tue Oct 31 23:56:41 2017 daemon.notice netifd: radio0 (29941): wlan0: AP-DISABLED
Tue Oct 31 23:56:41 2017 daemon.notice netifd: radio0 (29941): wlan0: Unable to setup interface.
Tue Oct 31 23:56:41 2017 kern.info kernel: [13659.880000] device wlan0 entered promiscuous mode
Tue Oct 31 23:56:41 2017 kern.info kernel: [13659.890000] device wlan0 left promiscuous mode
Tue Oct 31 23:56:41 2017 kern.info kernel: [13659.890000] br-lan: port 2(wlan0) entered disabled state
Tue Oct 31 23:56:41 2017 daemon.notice netifd: radio0 (29941): wlan0: interface state DISABLED->DISABLED
Tue Oct 31 23:56:41 2017 daemon.notice netifd: radio0 (29941): wlan0: AP-DISABLED
Tue Oct 31 23:56:41 2017 daemon.notice netifd: radio0 (29941): hostapd_free_hapd_data: Interface wlan0 wasn't started
Tue Oct 31 23:56:41 2017 daemon.notice netifd: radio0 (29941): nl80211: deinit ifname=wlan0 disabled_11b_rates=0
Tue Oct 31 23:56:41 2017 daemon.notice netifd: radio1 (29982): Configuration file: /var/run/hostapd-phy1.conf
Tue Oct 31 23:56:41 2017 daemon.notice netifd: radio0 (29941): cat: can't open '/var/run/wifi-phy0.pid': No such file or directory
Tue Oct 31 23:56:41 2017 daemon.notice netifd: radio0 (29941): Command failed: Invalid argument
Tue Oct 31 23:56:41 2017 daemon.notice netifd: radio0 (29941): Device setup failed: HOSTAPD_START_FAILED
Tue Oct 31 23:56:41 2017 kern.info kernel: [13660.020000] device wlan1 entered promiscuous mode
Tue Oct 31 23:56:41 2017 kern.info kernel: [13660.020000] br-lan: port 2(wlan1) entered forwarding state
Tue Oct 31 23:56:41 2017 kern.info kernel: [13660.030000] br-lan: port 2(wlan1) entered forwarding state
Tue Oct 31 23:56:41 2017 daemon.notice netifd: radio1 (29982): wlan1: interface state UNINITIALIZED->HT_SCAN
Tue Oct 31 23:56:42 2017 kern.info kernel: [13660.880000] br-lan: port 2(wlan1) entered disabled state
Tue Oct 31 23:56:43 2017 daemon.notice netifd: radio1 (29982): 20/40 MHz operation not permitted on channel pri=11 sec=7 based on overlapping BSSes
Tue Oct 31 23:56:43 2017 daemon.notice netifd: radio1 (29982): Using interface wlan1 with hwaddr f0:b4:29:58:bb:f0 and ssid "asdfghjkl"
Tue Oct 31 23:56:43 2017 kern.info kernel: [13661.620000] br-lan: port 2(wlan1) entered forwarding state
Tue Oct 31 23:56:43 2017 kern.info kernel: [13661.620000] br-lan: port 2(wlan1) entered forwarding state
Tue Oct 31 23:56:43 2017 daemon.notice netifd: radio1 (29982): wlan1: interface state HT_SCAN->ENABLED
Tue Oct 31 23:56:43 2017 daemon.notice netifd: radio1 (29982): wlan1: AP-ENABLED
Tue Oct 31 23:56:43 2017 daemon.notice netifd: Network device 'wlan1' link is up
Tue Oct 31 23:56:45 2017 kern.info kernel: [13663.620000] br-lan: port 2(wlan1) entered forwarding state
Tue Oct 31 23:57:00 2017 user.notice root: openvpn stopped, restarting
Tue Oct 31 23:57:01 2017 daemon.err openvpn(custom_config)[30217]: Options error: In [CMD-LINE]:1: Error opening configuration file: server.conf
Tue Oct 31 23:57:01 2017 daemon.warn openvpn(custom_config)[30217]: Use --help for more information.
Tue Oct 31 23:57:01 2017 daemon.info hostapd: wlan1: STA 78:02:f8:27:3e:3c IEEE 802.11: authenticated
Tue Oct 31 23:57:01 2017 daemon.info hostapd: wlan1: STA 78:02:f8:27:3e:3c IEEE 802.11: associated (aid 1)
Tue Oct 31 23:57:02 2017 daemon.info hostapd: wlan1: STA 78:02:f8:27:3e:3c RADIUS: starting accounting session E1D7D40C2E922151
Tue Oct 31 23:57:02 2017 daemon.info hostapd: wlan1: STA 78:02:f8:27:3e:3c WPA: pairwise key handshake completed (RSN)
Tue Oct 31 23:57:02 2017 daemon.info dnsmasq-dhcp[26370]: DHCPDISCOVER(br-lan) 78:02:f8:27:3e:3c
Tue Oct 31 23:57:02 2017 daemon.info dnsmasq-dhcp[26370]: DHCPOFFER(br-lan) 10.0.0.246 78:02:f8:27:3e:3c
Tue Oct 31 23:57:02 2017 daemon.info dnsmasq-dhcp[26370]: DHCPREQUEST(br-lan) 10.0.0.246 78:02:f8:27:3e:3c
Tue Oct 31 23:57:02 2017 daemon.info dnsmasq-dhcp[26370]: DHCPACK(br-lan) 10.0.0.246 78:02:f8:27:3e:3c MI5s-denleo
Tue Oct 31 23:57:04 2017 kern.info kernel: [13682.730000] device wlan1 left promiscuous mode
Tue Oct 31 23:57:04 2017 kern.info kernel: [13682.730000] br-lan: port 2(wlan1) entered disabled state
Tue Oct 31 23:57:04 2017 daemon.notice netifd: Network device 'wlan1' link is down
Tue Oct 31 23:57:04 2017 daemon.notice netifd: radio1 (30271): command failed: Operation not supported (-122)
Tue Oct 31 23:57:04 2017 daemon.notice netifd: radio0 (30247): Configuration file: /var/run/hostapd-phy0.conf
Tue Oct 31 23:57:05 2017 daemon.notice netifd: radio1 (30271): Configuration file: /var/run/hostapd-phy1.conf
Tue Oct 31 23:57:05 2017 daemon.notice netifd: radio0 (30247): wlan0: IEEE 802.11 Configured channel (52) not found from the channel list of current mode (2) IEEE 802.11a
Tue Oct 31 23:57:05 2017 daemon.warn hostapd: wlan0: IEEE 802.11 Configured channel (52) not found from the channel list of current mode (2) IEEE 802.11a
Tue Oct 31 23:57:05 2017 daemon.notice netifd: radio0 (30247): wlan0: IEEE 802.11 Hardware does not support configured channel
Tue Oct 31 23:57:05 2017 kern.info kernel: [13683.800000] device wlan0 entered promiscuous mode
Tue Oct 31 23:57:05 2017 daemon.warn hostapd: wlan0: IEEE 802.11 Hardware does not support configured channel
Tue Oct 31 23:57:05 2017 kern.info kernel: [13683.810000] device wlan0 left promiscuous mode
Tue Oct 31 23:57:05 2017 kern.info kernel: [13683.810000] br-lan: port 2(wlan0) entered disabled state
Tue Oct 31 23:57:05 2017 daemon.notice netifd: radio0 (30247): Could not select hw_mode and channel. (-3)
Tue Oct 31 23:57:05 2017 daemon.notice netifd: radio0 (30247): wlan0: interface state UNINITIALIZED->DISABLED
Tue Oct 31 23:57:05 2017 daemon.notice netifd: radio0 (30247): wlan0: AP-DISABLED
Tue Oct 31 23:57:05 2017 daemon.notice netifd: radio0 (30247): wlan0: Unable to setup interface.
Tue Oct 31 23:57:05 2017 daemon.notice netifd: radio0 (30247): wlan0: interface state DISABLED->DISABLED
Tue Oct 31 23:57:05 2017 daemon.notice netifd: radio0 (30247): wlan0: AP-DISABLED
Tue Oct 31 23:57:05 2017 daemon.notice netifd: radio0 (30247): hostapd_free_hapd_data: Interface wlan0 wasn't started
Tue Oct 31 23:57:05 2017 daemon.notice netifd: radio0 (30247): nl80211: deinit ifname=wlan0 disabled_11b_rates=0
Tue Oct 31 23:57:05 2017 daemon.notice netifd: radio0 (30247): cat: can't open '/var/run/wifi-phy0.pid': No such file or directory
Tue Oct 31 23:57:05 2017 daemon.notice netifd: radio0 (30247): Command failed: Invalid argument
Tue Oct 31 23:57:05 2017 daemon.notice netifd: radio0 (30247): Device setup failed: HOSTAPD_START_FAILED
Tue Oct 31 23:57:05 2017 kern.info kernel: [13683.920000] device wlan1 entered promiscuous mode
Tue Oct 31 23:57:05 2017 kern.info kernel: [13683.920000] br-lan: port 2(wlan1) entered forwarding state
Tue Oct 31 23:57:05 2017 kern.info kernel: [13683.930000] br-lan: port 2(wlan1) entered forwarding state
Tue Oct 31 23:57:05 2017 daemon.notice netifd: radio1 (30271): wlan1: interface state UNINITIALIZED->HT_SCAN
Tue Oct 31 23:57:06 2017 kern.info kernel: [13684.770000] br-lan: port 2(wlan1) entered disabled state
Tue Oct 31 23:57:06 2017 daemon.notice netifd: radio1 (30271): 20/40 MHz operation not permitted on channel pri=11 sec=7 based on overlapping BSSes
Tue Oct 31 23:57:06 2017 daemon.notice netifd: radio1 (30271): Using interface wlan1 with hwaddr f0:b4:29:58:bb:f0 and ssid "asdfghjkl"
Tue Oct 31 23:57:07 2017 kern.info kernel: [13685.520000] br-lan: port 2(wlan1) entered forwarding state
Tue Oct 31 23:57:07 2017 kern.info kernel: [13685.520000] br-lan: port 2(wlan1) entered forwarding state
Tue Oct 31 23:57:07 2017 daemon.notice netifd: radio1 (30271): wlan1: interface state HT_SCAN->ENABLED
Tue Oct 31 23:57:07 2017 daemon.notice netifd: radio1 (30271): wlan1: AP-ENABLED
Tue Oct 31 23:57:07 2017 daemon.notice netifd: Network device 'wlan1' link is up
Tue Oct 31 23:57:09 2017 kern.info kernel: [13687.520000] br-lan: port 2(wlan1) entered forwarding state
Tue Oct 31 23:58:00 2017 user.notice root: openvpn stopped, restarting
Tue Oct 31 23:58:01 2017 daemon.err openvpn(custom_config)[30522]: Options error: In [CMD-LINE]:1: Error opening configuration file: server.conf
Tue Oct 31 23:58:01 2017 daemon.warn openvpn(custom_config)[30522]: Use --help for more information.
Tue Oct 31 23:58:06 2017 daemon.info hostapd: wlan1: STA 78:02:f8:27:3e:3c IEEE 802.11: authenticated
Tue Oct 31 23:58:06 2017 daemon.info hostapd: wlan1: STA 78:02:f8:27:3e:3c IEEE 802.11: associated (aid 1)
Tue Oct 31 23:58:07 2017 daemon.info hostapd: wlan1: STA 78:02:f8:27:3e:3c RADIUS: starting accounting session 6BE16570A6893FB6
Tue Oct 31 23:58:07 2017 daemon.info hostapd: wlan1: STA 78:02:f8:27:3e:3c WPA: pairwise key handshake completed (RSN)
Tue Oct 31 23:58:07 2017 daemon.info dnsmasq-dhcp[26370]: DHCPDISCOVER(br-lan) 78:02:f8:27:3e:3c
Tue Oct 31 23:58:07 2017 daemon.info dnsmasq-dhcp[26370]: DHCPOFFER(br-lan) 10.0.0.246 78:02:f8:27:3e:3c
Tue Oct 31 23:58:07 2017 daemon.info dnsmasq-dhcp[26370]: DHCPREQUEST(br-lan) 10.0.0.246 78:02:f8:27:3e:3c
Tue Oct 31 23:58:07 2017 daemon.info dnsmasq-dhcp[26370]: DHCPACK(br-lan) 10.0.0.246 78:02:f8:27:3e:3c MI5s-denleo
Tue Oct 31 23:59:00 2017 user.notice root: openvpn stopped, restarting
Tue Oct 31 23:59:01 2017 daemon.err openvpn(custom_config)[30555]: Options error: In [CMD-LINE]:1: Error opening configuration file: server.conf
Tue Oct 31 23:59:01 2017 daemon.warn openvpn(custom_config)[30555]: Use --help for more information.
Tue Oct 31 23:59:17 2017 authpriv.info dropbear[29022]: Exit before auth: Timeout before auth
Tue Oct 31 23:59:21 2017 kern.info kernel: [13819.910000] device wlan1 left promiscuous mode
Tue Oct 31 23:59:21 2017 kern.info kernel: [13819.910000] br-lan: port 2(wlan1) entered disabled state
Tue Oct 31 23:59:21 2017 daemon.notice netifd: Network device 'wlan1' link is down
Tue Oct 31 23:59:21 2017 daemon.notice netifd: radio1 (30592): command failed: Operation not supported (-122)
Tue Oct 31 23:59:22 2017 daemon.notice netifd: radio0 (30572): Configuration file: /var/run/hostapd-phy0.conf
Tue Oct 31 23:59:22 2017 daemon.notice netifd: radio1 (30592): Configuration file: /var/run/hostapd-phy1.conf
Tue Oct 31 23:59:22 2017 daemon.notice netifd: radio0 (30572): wlan0: IEEE 802.11 Configured channel (52) not found from the channel list of current mode (2) IEEE 802.11a
Tue Oct 31 23:59:22 2017 daemon.warn hostapd: wlan0: IEEE 802.11 Configured channel (52) not found from the channel list of current mode (2) IEEE 802.11a
Tue Oct 31 23:59:22 2017 kern.info kernel: [13820.980000] device wlan0 entered promiscuous mode
Tue Oct 31 23:59:22 2017 daemon.warn hostapd: wlan0: IEEE 802.11 Hardware does not support configured channel
Tue Oct 31 23:59:22 2017 kern.info kernel: [13820.990000] device wlan0 left promiscuous mode
Tue Oct 31 23:59:22 2017 kern.info kernel: [13820.990000] br-lan: port 2(wlan0) entered disabled state
Tue Oct 31 23:59:22 2017 daemon.notice netifd: radio0 (30572): wlan0: IEEE 802.11 Hardware does not support configured channel
Tue Oct 31 23:59:22 2017 daemon.notice netifd: radio0 (30572): Could not select hw_mode and channel. (-3)
Tue Oct 31 23:59:22 2017 daemon.notice netifd: radio0 (30572): wlan0: interface state UNINITIALIZED->DISABLED
Tue Oct 31 23:59:22 2017 daemon.notice netifd: radio0 (30572): wlan0: AP-DISABLED
Tue Oct 31 23:59:22 2017 daemon.notice netifd: radio0 (30572): wlan0: Unable to setup interface.
Tue Oct 31 23:59:22 2017 daemon.notice netifd: radio0 (30572): wlan0: interface state DISABLED->DISABLED
Tue Oct 31 23:59:22 2017 daemon.notice netifd: radio0 (30572): wlan0: AP-DISABLED
Tue Oct 31 23:59:22 2017 daemon.notice netifd: radio0 (30572): hostapd_free_hapd_data: Interface wlan0 wasn't started
Tue Oct 31 23:59:22 2017 daemon.notice netifd: radio0 (30572): nl80211: deinit ifname=wlan0 disabled_11b_rates=0
Tue Oct 31 23:59:22 2017 daemon.notice netifd: radio0 (30572): cat: can't open '/var/run/wifi-phy0.pid': No such file or directory
Tue Oct 31 23:59:22 2017 kern.info kernel: [13821.090000] device wlan1 entered promiscuous mode
Tue Oct 31 23:59:22 2017 kern.info kernel: [13821.090000] br-lan: port 2(wlan1) entered forwarding state
Tue Oct 31 23:59:22 2017 kern.info kernel: [13821.100000] br-lan: port 2(wlan1) entered forwarding state
Tue Oct 31 23:59:22 2017 daemon.notice netifd: radio1 (30592): wlan1: interface state UNINITIALIZED->HT_SCAN
Tue Oct 31 23:59:22 2017 daemon.notice netifd: radio0 (30572): Command failed: Invalid argument
Tue Oct 31 23:59:22 2017 daemon.notice netifd: radio0 (30572): Device setup failed: HOSTAPD_START_FAILED
Tue Oct 31 23:59:23 2017 kern.info kernel: [13821.950000] br-lan: port 2(wlan1) entered disabled state
Tue Oct 31 23:59:24 2017 daemon.notice netifd: radio1 (30592): 20/40 MHz operation not permitted on channel pri=11 sec=7 based on overlapping BSSes
Tue Oct 31 23:59:24 2017 daemon.notice netifd: radio1 (30592): Using interface wlan1 with hwaddr f0:b4:29:58:bb:f0 and ssid "asdfghjkl"
Tue Oct 31 23:59:24 2017 kern.info kernel: [13822.690000] br-lan: port 2(wlan1) entered forwarding state
Tue Oct 31 23:59:24 2017 kern.info kernel: [13822.690000] br-lan: port 2(wlan1) entered forwarding state
Tue Oct 31 23:59:24 2017 daemon.notice netifd: radio1 (30592): wlan1: interface state HT_SCAN->ENABLED
Tue Oct 31 23:59:24 2017 daemon.notice netifd: radio1 (30592): wlan1: AP-ENABLED
Tue Oct 31 23:59:24 2017 daemon.notice netifd: Network device 'wlan1' link is up
Tue Oct 31 23:59:26 2017 kern.info kernel: [13824.690000] br-lan: port 2(wlan1) entered forwarding state
Success
-
- Posts: 44
- Joined: Mon Jan 27, 2014 5:28 pm
- Location: Bukarest
Re: Version 1.10.0 : New stable version with critical security fixes
No problems till now (1.10.0)
TP-Link TL-WR1043ND v1
Re: Version 1.10.0 : New stable version with critical security fixes
Greetings All,mckman wrote:Greetings All,
Just reporting that I upgraded my WNDRMACv2 and WNDR3700v1 units to version 1.10.0 from 1.9.x from September 18, 2017. Did not preserve the settings. On the WNDRMACv2, I tested DDNS, OpenVPN, AdBlock Plugin, USB Camera, QOS w/ACC and WIFI (Both 2.4Ghz and 5Ghz). All seems to be functioning great!. On the WNDR3700v1, I tested USB Printing, it functions great as well. I also have 2 vlans (guest network completely segragated from regular network with internet only access) and vlan tagging setup between these 2 units and it is functioning great as well.
The only strange anomaly is that the WNDRMACv2 seems to always report an idle of around 0.72.
https://imgur.com/F8XZen4
I've tried turning off openvpn, AdBlock plugin, QOS w/ACC, WIFI, and turning off Bandwidth monitoring through SSH and the idle usage never goes below 0.69. I've reflashed the firmware and it still shows the same usage even after a couple of factory defaulting. I experienced the same issue with the 1.9.x from September 18, 2017 as well. I don't experience any slow downs on the network, everything seems to be snappy with the web interface. When I SSH into the unit and do a top command, I see know excessive usage in memory or processor. Go figure.
Just reporting that I found the source of my high idle cpu load issue with the WNDRMACv2 unit with the 1.10 firmware. I had a USB 2.0 hub plugged into the unit along with a couple of webcams that I forgot was plugged into the unit until I physically looked at the back of the unit this evening. Once I unplugged the USB hub, cpu load dropped down to 0.00 almost instantaneously. Never had this issue with firmware 1.6.x on this unit and this USB hub and high idle load but it seems to be an issue with 1.9 and 1.10 or perhaps with just this USB 2.0 hub I had plugged into the unit. Everything is all good and just as snappy as ever.
Netgear WNDR3700 v1
Netgear WNDRMAC v2
TP-Link MR3020 v1.8
TP-Link WR743ND v1
Netgear WNDRMAC v2
TP-Link MR3020 v1.8
TP-Link WR743ND v1
Re: Version 1.10.0 : New stable version with critical security fixes
In your screenshot it says you are selecting channel 149. In this log it shows 52.kanenas wrote:Please provide more info, I just ssh to it and used the command wifi enable and then dmesgLantis wrote:Can you please provide a “dmesg” and “logread” 30 seconds after issuing a “wifi” command at the command line?and using the logread plug inCode: Select all
[13660.020000] device wlan1 entered promiscuous mode [13660.020000] br-lan: port 2(wlan1) entered forwarding state [13660.030000] br-lan: port 2(wlan1) entered forwarding state [13660.880000] br-lan: port 2(wlan1) entered disabled state [13661.620000] br-lan: port 2(wlan1) entered forwarding state [13661.620000] br-lan: port 2(wlan1) entered forwarding state [13663.620000] br-lan: port 2(wlan1) entered forwarding state [13682.730000] device wlan1 left promiscuous mode [13682.730000] br-lan: port 2(wlan1) entered disabled state [13683.800000] device wlan0 entered promiscuous mode [13683.810000] device wlan0 left promiscuous mode [13683.810000] br-lan: port 2(wlan0) entered disabled state [13683.920000] device wlan1 entered promiscuous mode [13683.920000] br-lan: port 2(wlan1) entered forwarding state [13683.930000] br-lan: port 2(wlan1) entered forwarding state [13684.770000] br-lan: port 2(wlan1) entered disabled state [13685.520000] br-lan: port 2(wlan1) entered forwarding state [13685.520000] br-lan: port 2(wlan1) entered forwarding state [13687.520000] br-lan: port 2(wlan1) entered forwarding state [13819.910000] device wlan1 left promiscuous mode [13819.910000] br-lan: port 2(wlan1) entered disabled state [13820.980000] device wlan0 entered promiscuous mode [13820.990000] device wlan0 left promiscuous mode [13820.990000] br-lan: port 2(wlan0) entered disabled state [13821.090000] device wlan1 entered promiscuous mode [13821.090000] br-lan: port 2(wlan1) entered forwarding state [13821.100000] br-lan: port 2(wlan1) entered forwarding state [13821.950000] br-lan: port 2(wlan1) entered disabled state
Code: Select all
Tue Oct 31 23:56:34 2017 daemon.notice netifd: Network device 'wlan1' link is down Tue Oct 31 23:56:34 2017 daemon.notice netifd: radio1 (29707): command failed: Operation not supported (-122) Tue Oct 31 23:56:34 2017 daemon.notice netifd: radio0 (29671): Configuration file: /var/run/hostapd-phy0.conf Tue Oct 31 23:56:35 2017 daemon.notice netifd: radio1 (29707): Configuration file: /var/run/hostapd-phy1.conf Tue Oct 31 23:56:35 2017 daemon.notice netifd: radio0 (29671): wlan0: IEEE 802.11 Configured channel (52) not found from the channel list of current mode (2) IEEE 802.11a Tue Oct 31 23:56:35 2017 kern.info kernel: [13653.520000] device wlan0 entered promiscuous mode Tue Oct 31 23:56:35 2017 daemon.warn hostapd: wlan0: IEEE 802.11 Configured channel (52) not found from the channel list of current mode (2) IEEE 802.11a Tue Oct 31 23:56:35 2017 daemon.notice netifd: radio0 (29671): wlan0: IEEE 802.11 Hardware does not support configured channel Tue Oct 31 23:56:35 2017 daemon.warn hostapd: wlan0: IEEE 802.11 Hardware does not support configured channel Tue Oct 31 23:56:35 2017 daemon.notice netifd: radio0 (29671): Could not select hw_mode and channel. (-3) Tue Oct 31 23:56:35 2017 daemon.notice netifd: radio0 (29671): wlan0: interface state UNINITIALIZED->DISABLED Tue Oct 31 23:56:35 2017 daemon.notice netifd: radio0 (29671): wlan0: AP-DISABLED Tue Oct 31 23:56:35 2017 daemon.notice netifd: radio0 (29671): wlan0: Unable to setup interface. Tue Oct 31 23:56:35 2017 daemon.notice netifd: radio0 (29671): wlan0: interface state DISABLED->DISABLED Tue Oct 31 23:56:35 2017 daemon.notice netifd: radio0 (29671): wlan0: AP-DISABLED Tue Oct 31 23:56:35 2017 daemon.notice netifd: radio0 (29671): hostapd_free_hapd_data: Interface wlan0 wasn't started Tue Oct 31 23:56:35 2017 daemon.notice netifd: radio0 (29671): nl80211: deinit ifname=wlan0 disabled_11b_rates=0 Tue Oct 31 23:56:35 2017 kern.info kernel: [13653.600000] device wlan0 left promiscuous mode Tue Oct 31 23:56:35 2017 kern.info kernel: [13653.610000] br-lan: port 2(wlan0) entered disabled state Tue Oct 31 23:56:35 2017 daemon.notice netifd: radio0 (29671): cat: can't open '/var/run/wifi-phy0.pid': No such file or directory Tue Oct 31 23:56:35 2017 kern.info kernel: [13653.630000] device wlan1 entered promiscuous mode Tue Oct 31 23:56:35 2017 kern.info kernel: [13653.630000] br-lan: port 2(wlan1) entered forwarding state Tue Oct 31 23:56:35 2017 kern.info kernel: [13653.640000] br-lan: port 2(wlan1) entered forwarding state Tue Oct 31 23:56:35 2017 daemon.notice netifd: radio1 (29707): wlan1: interface state UNINITIALIZED->HT_SCAN Tue Oct 31 23:56:35 2017 daemon.notice netifd: radio0 (29671): Command failed: Invalid argument Tue Oct 31 23:56:35 2017 daemon.notice netifd: radio0 (29671): Device setup failed: HOSTAPD_START_FAILED Tue Oct 31 23:56:36 2017 kern.info kernel: [13654.490000] br-lan: port 2(wlan1) entered disabled state Tue Oct 31 23:56:36 2017 daemon.notice netifd: radio1 (29707): 20/40 MHz operation not permitted on channel pri=11 sec=7 based on overlapping BSSes Tue Oct 31 23:56:36 2017 daemon.notice netifd: radio1 (29707): Using interface wlan1 with hwaddr f0:b4:29:58:bb:f0 and ssid "asdfghjkl" Tue Oct 31 23:56:36 2017 kern.info kernel: [13655.230000] br-lan: port 2(wlan1) entered forwarding state Tue Oct 31 23:56:36 2017 kern.info kernel: [13655.230000] br-lan: port 2(wlan1) entered forwarding state Tue Oct 31 23:56:36 2017 daemon.notice netifd: radio1 (29707): wlan1: interface state HT_SCAN->ENABLED Tue Oct 31 23:56:36 2017 daemon.notice netifd: radio1 (29707): wlan1: AP-ENABLED Tue Oct 31 23:56:36 2017 daemon.notice netifd: Network device 'wlan1' link is up Tue Oct 31 23:56:38 2017 kern.info kernel: [13657.230000] br-lan: port 2(wlan1) entered forwarding state Tue Oct 31 23:56:40 2017 kern.info kernel: [13658.850000] device wlan1 left promiscuous mode Tue Oct 31 23:56:40 2017 kern.info kernel: [13658.850000] br-lan: port 2(wlan1) entered disabled state Tue Oct 31 23:56:40 2017 daemon.notice netifd: Network device 'wlan1' link is down Tue Oct 31 23:56:40 2017 daemon.notice netifd: radio1 (29982): command failed: Operation not supported (-122) Tue Oct 31 23:56:41 2017 daemon.notice netifd: radio0 (29941): Configuration file: /var/run/hostapd-phy0.conf Tue Oct 31 23:56:41 2017 daemon.warn hostapd: wlan0: IEEE 802.11 Configured channel (52) not found from the channel list of current mode (2) IEEE 802.11a Tue Oct 31 23:56:41 2017 daemon.warn hostapd: wlan0: IEEE 802.11 Hardware does not support configured channel Tue Oct 31 23:56:41 2017 daemon.notice netifd: radio0 (29941): wlan0: IEEE 802.11 Configured channel (52) not found from the channel list of current mode (2) IEEE 802.11a Tue Oct 31 23:56:41 2017 daemon.notice netifd: radio0 (29941): wlan0: IEEE 802.11 Hardware does not support configured channel Tue Oct 31 23:56:41 2017 daemon.notice netifd: radio0 (29941): Could not select hw_mode and channel. (-3) Tue Oct 31 23:56:41 2017 daemon.notice netifd: radio0 (29941): wlan0: interface state UNINITIALIZED->DISABLED Tue Oct 31 23:56:41 2017 daemon.notice netifd: radio0 (29941): wlan0: AP-DISABLED Tue Oct 31 23:56:41 2017 daemon.notice netifd: radio0 (29941): wlan0: Unable to setup interface. Tue Oct 31 23:56:41 2017 kern.info kernel: [13659.880000] device wlan0 entered promiscuous mode Tue Oct 31 23:56:41 2017 kern.info kernel: [13659.890000] device wlan0 left promiscuous mode Tue Oct 31 23:56:41 2017 kern.info kernel: [13659.890000] br-lan: port 2(wlan0) entered disabled state Tue Oct 31 23:56:41 2017 daemon.notice netifd: radio0 (29941): wlan0: interface state DISABLED->DISABLED Tue Oct 31 23:56:41 2017 daemon.notice netifd: radio0 (29941): wlan0: AP-DISABLED Tue Oct 31 23:56:41 2017 daemon.notice netifd: radio0 (29941): hostapd_free_hapd_data: Interface wlan0 wasn't started Tue Oct 31 23:56:41 2017 daemon.notice netifd: radio0 (29941): nl80211: deinit ifname=wlan0 disabled_11b_rates=0 Tue Oct 31 23:56:41 2017 daemon.notice netifd: radio1 (29982): Configuration file: /var/run/hostapd-phy1.conf Tue Oct 31 23:56:41 2017 daemon.notice netifd: radio0 (29941): cat: can't open '/var/run/wifi-phy0.pid': No such file or directory Tue Oct 31 23:56:41 2017 daemon.notice netifd: radio0 (29941): Command failed: Invalid argument Tue Oct 31 23:56:41 2017 daemon.notice netifd: radio0 (29941): Device setup failed: HOSTAPD_START_FAILED Tue Oct 31 23:56:41 2017 kern.info kernel: [13660.020000] device wlan1 entered promiscuous mode Tue Oct 31 23:56:41 2017 kern.info kernel: [13660.020000] br-lan: port 2(wlan1) entered forwarding state Tue Oct 31 23:56:41 2017 kern.info kernel: [13660.030000] br-lan: port 2(wlan1) entered forwarding state Tue Oct 31 23:56:41 2017 daemon.notice netifd: radio1 (29982): wlan1: interface state UNINITIALIZED->HT_SCAN Tue Oct 31 23:56:42 2017 kern.info kernel: [13660.880000] br-lan: port 2(wlan1) entered disabled state Tue Oct 31 23:56:43 2017 daemon.notice netifd: radio1 (29982): 20/40 MHz operation not permitted on channel pri=11 sec=7 based on overlapping BSSes Tue Oct 31 23:56:43 2017 daemon.notice netifd: radio1 (29982): Using interface wlan1 with hwaddr f0:b4:29:58:bb:f0 and ssid "asdfghjkl" Tue Oct 31 23:56:43 2017 kern.info kernel: [13661.620000] br-lan: port 2(wlan1) entered forwarding state Tue Oct 31 23:56:43 2017 kern.info kernel: [13661.620000] br-lan: port 2(wlan1) entered forwarding state Tue Oct 31 23:56:43 2017 daemon.notice netifd: radio1 (29982): wlan1: interface state HT_SCAN->ENABLED Tue Oct 31 23:56:43 2017 daemon.notice netifd: radio1 (29982): wlan1: AP-ENABLED Tue Oct 31 23:56:43 2017 daemon.notice netifd: Network device 'wlan1' link is up Tue Oct 31 23:56:45 2017 kern.info kernel: [13663.620000] br-lan: port 2(wlan1) entered forwarding state Tue Oct 31 23:57:00 2017 user.notice root: openvpn stopped, restarting Tue Oct 31 23:57:01 2017 daemon.err openvpn(custom_config)[30217]: Options error: In [CMD-LINE]:1: Error opening configuration file: server.conf Tue Oct 31 23:57:01 2017 daemon.warn openvpn(custom_config)[30217]: Use --help for more information. Tue Oct 31 23:57:01 2017 daemon.info hostapd: wlan1: STA 78:02:f8:27:3e:3c IEEE 802.11: authenticated Tue Oct 31 23:57:01 2017 daemon.info hostapd: wlan1: STA 78:02:f8:27:3e:3c IEEE 802.11: associated (aid 1) Tue Oct 31 23:57:02 2017 daemon.info hostapd: wlan1: STA 78:02:f8:27:3e:3c RADIUS: starting accounting session E1D7D40C2E922151 Tue Oct 31 23:57:02 2017 daemon.info hostapd: wlan1: STA 78:02:f8:27:3e:3c WPA: pairwise key handshake completed (RSN) Tue Oct 31 23:57:02 2017 daemon.info dnsmasq-dhcp[26370]: DHCPDISCOVER(br-lan) 78:02:f8:27:3e:3c Tue Oct 31 23:57:02 2017 daemon.info dnsmasq-dhcp[26370]: DHCPOFFER(br-lan) 10.0.0.246 78:02:f8:27:3e:3c Tue Oct 31 23:57:02 2017 daemon.info dnsmasq-dhcp[26370]: DHCPREQUEST(br-lan) 10.0.0.246 78:02:f8:27:3e:3c Tue Oct 31 23:57:02 2017 daemon.info dnsmasq-dhcp[26370]: DHCPACK(br-lan) 10.0.0.246 78:02:f8:27:3e:3c MI5s-denleo Tue Oct 31 23:57:04 2017 kern.info kernel: [13682.730000] device wlan1 left promiscuous mode Tue Oct 31 23:57:04 2017 kern.info kernel: [13682.730000] br-lan: port 2(wlan1) entered disabled state Tue Oct 31 23:57:04 2017 daemon.notice netifd: Network device 'wlan1' link is down Tue Oct 31 23:57:04 2017 daemon.notice netifd: radio1 (30271): command failed: Operation not supported (-122) Tue Oct 31 23:57:04 2017 daemon.notice netifd: radio0 (30247): Configuration file: /var/run/hostapd-phy0.conf Tue Oct 31 23:57:05 2017 daemon.notice netifd: radio1 (30271): Configuration file: /var/run/hostapd-phy1.conf Tue Oct 31 23:57:05 2017 daemon.notice netifd: radio0 (30247): wlan0: IEEE 802.11 Configured channel (52) not found from the channel list of current mode (2) IEEE 802.11a Tue Oct 31 23:57:05 2017 daemon.warn hostapd: wlan0: IEEE 802.11 Configured channel (52) not found from the channel list of current mode (2) IEEE 802.11a Tue Oct 31 23:57:05 2017 daemon.notice netifd: radio0 (30247): wlan0: IEEE 802.11 Hardware does not support configured channel Tue Oct 31 23:57:05 2017 kern.info kernel: [13683.800000] device wlan0 entered promiscuous mode Tue Oct 31 23:57:05 2017 daemon.warn hostapd: wlan0: IEEE 802.11 Hardware does not support configured channel Tue Oct 31 23:57:05 2017 kern.info kernel: [13683.810000] device wlan0 left promiscuous mode Tue Oct 31 23:57:05 2017 kern.info kernel: [13683.810000] br-lan: port 2(wlan0) entered disabled state Tue Oct 31 23:57:05 2017 daemon.notice netifd: radio0 (30247): Could not select hw_mode and channel. (-3) Tue Oct 31 23:57:05 2017 daemon.notice netifd: radio0 (30247): wlan0: interface state UNINITIALIZED->DISABLED Tue Oct 31 23:57:05 2017 daemon.notice netifd: radio0 (30247): wlan0: AP-DISABLED Tue Oct 31 23:57:05 2017 daemon.notice netifd: radio0 (30247): wlan0: Unable to setup interface. Tue Oct 31 23:57:05 2017 daemon.notice netifd: radio0 (30247): wlan0: interface state DISABLED->DISABLED Tue Oct 31 23:57:05 2017 daemon.notice netifd: radio0 (30247): wlan0: AP-DISABLED Tue Oct 31 23:57:05 2017 daemon.notice netifd: radio0 (30247): hostapd_free_hapd_data: Interface wlan0 wasn't started Tue Oct 31 23:57:05 2017 daemon.notice netifd: radio0 (30247): nl80211: deinit ifname=wlan0 disabled_11b_rates=0 Tue Oct 31 23:57:05 2017 daemon.notice netifd: radio0 (30247): cat: can't open '/var/run/wifi-phy0.pid': No such file or directory Tue Oct 31 23:57:05 2017 daemon.notice netifd: radio0 (30247): Command failed: Invalid argument Tue Oct 31 23:57:05 2017 daemon.notice netifd: radio0 (30247): Device setup failed: HOSTAPD_START_FAILED Tue Oct 31 23:57:05 2017 kern.info kernel: [13683.920000] device wlan1 entered promiscuous mode Tue Oct 31 23:57:05 2017 kern.info kernel: [13683.920000] br-lan: port 2(wlan1) entered forwarding state Tue Oct 31 23:57:05 2017 kern.info kernel: [13683.930000] br-lan: port 2(wlan1) entered forwarding state Tue Oct 31 23:57:05 2017 daemon.notice netifd: radio1 (30271): wlan1: interface state UNINITIALIZED->HT_SCAN Tue Oct 31 23:57:06 2017 kern.info kernel: [13684.770000] br-lan: port 2(wlan1) entered disabled state Tue Oct 31 23:57:06 2017 daemon.notice netifd: radio1 (30271): 20/40 MHz operation not permitted on channel pri=11 sec=7 based on overlapping BSSes Tue Oct 31 23:57:06 2017 daemon.notice netifd: radio1 (30271): Using interface wlan1 with hwaddr f0:b4:29:58:bb:f0 and ssid "asdfghjkl" Tue Oct 31 23:57:07 2017 kern.info kernel: [13685.520000] br-lan: port 2(wlan1) entered forwarding state Tue Oct 31 23:57:07 2017 kern.info kernel: [13685.520000] br-lan: port 2(wlan1) entered forwarding state Tue Oct 31 23:57:07 2017 daemon.notice netifd: radio1 (30271): wlan1: interface state HT_SCAN->ENABLED Tue Oct 31 23:57:07 2017 daemon.notice netifd: radio1 (30271): wlan1: AP-ENABLED Tue Oct 31 23:57:07 2017 daemon.notice netifd: Network device 'wlan1' link is up Tue Oct 31 23:57:09 2017 kern.info kernel: [13687.520000] br-lan: port 2(wlan1) entered forwarding state Tue Oct 31 23:58:00 2017 user.notice root: openvpn stopped, restarting Tue Oct 31 23:58:01 2017 daemon.err openvpn(custom_config)[30522]: Options error: In [CMD-LINE]:1: Error opening configuration file: server.conf Tue Oct 31 23:58:01 2017 daemon.warn openvpn(custom_config)[30522]: Use --help for more information. Tue Oct 31 23:58:06 2017 daemon.info hostapd: wlan1: STA 78:02:f8:27:3e:3c IEEE 802.11: authenticated Tue Oct 31 23:58:06 2017 daemon.info hostapd: wlan1: STA 78:02:f8:27:3e:3c IEEE 802.11: associated (aid 1) Tue Oct 31 23:58:07 2017 daemon.info hostapd: wlan1: STA 78:02:f8:27:3e:3c RADIUS: starting accounting session 6BE16570A6893FB6 Tue Oct 31 23:58:07 2017 daemon.info hostapd: wlan1: STA 78:02:f8:27:3e:3c WPA: pairwise key handshake completed (RSN) Tue Oct 31 23:58:07 2017 daemon.info dnsmasq-dhcp[26370]: DHCPDISCOVER(br-lan) 78:02:f8:27:3e:3c Tue Oct 31 23:58:07 2017 daemon.info dnsmasq-dhcp[26370]: DHCPOFFER(br-lan) 10.0.0.246 78:02:f8:27:3e:3c Tue Oct 31 23:58:07 2017 daemon.info dnsmasq-dhcp[26370]: DHCPREQUEST(br-lan) 10.0.0.246 78:02:f8:27:3e:3c Tue Oct 31 23:58:07 2017 daemon.info dnsmasq-dhcp[26370]: DHCPACK(br-lan) 10.0.0.246 78:02:f8:27:3e:3c MI5s-denleo Tue Oct 31 23:59:00 2017 user.notice root: openvpn stopped, restarting Tue Oct 31 23:59:01 2017 daemon.err openvpn(custom_config)[30555]: Options error: In [CMD-LINE]:1: Error opening configuration file: server.conf Tue Oct 31 23:59:01 2017 daemon.warn openvpn(custom_config)[30555]: Use --help for more information. Tue Oct 31 23:59:17 2017 authpriv.info dropbear[29022]: Exit before auth: Timeout before auth Tue Oct 31 23:59:21 2017 kern.info kernel: [13819.910000] device wlan1 left promiscuous mode Tue Oct 31 23:59:21 2017 kern.info kernel: [13819.910000] br-lan: port 2(wlan1) entered disabled state Tue Oct 31 23:59:21 2017 daemon.notice netifd: Network device 'wlan1' link is down Tue Oct 31 23:59:21 2017 daemon.notice netifd: radio1 (30592): command failed: Operation not supported (-122) Tue Oct 31 23:59:22 2017 daemon.notice netifd: radio0 (30572): Configuration file: /var/run/hostapd-phy0.conf Tue Oct 31 23:59:22 2017 daemon.notice netifd: radio1 (30592): Configuration file: /var/run/hostapd-phy1.conf Tue Oct 31 23:59:22 2017 daemon.notice netifd: radio0 (30572): wlan0: IEEE 802.11 Configured channel (52) not found from the channel list of current mode (2) IEEE 802.11a Tue Oct 31 23:59:22 2017 daemon.warn hostapd: wlan0: IEEE 802.11 Configured channel (52) not found from the channel list of current mode (2) IEEE 802.11a Tue Oct 31 23:59:22 2017 kern.info kernel: [13820.980000] device wlan0 entered promiscuous mode Tue Oct 31 23:59:22 2017 daemon.warn hostapd: wlan0: IEEE 802.11 Hardware does not support configured channel Tue Oct 31 23:59:22 2017 kern.info kernel: [13820.990000] device wlan0 left promiscuous mode Tue Oct 31 23:59:22 2017 kern.info kernel: [13820.990000] br-lan: port 2(wlan0) entered disabled state Tue Oct 31 23:59:22 2017 daemon.notice netifd: radio0 (30572): wlan0: IEEE 802.11 Hardware does not support configured channel Tue Oct 31 23:59:22 2017 daemon.notice netifd: radio0 (30572): Could not select hw_mode and channel. (-3) Tue Oct 31 23:59:22 2017 daemon.notice netifd: radio0 (30572): wlan0: interface state UNINITIALIZED->DISABLED Tue Oct 31 23:59:22 2017 daemon.notice netifd: radio0 (30572): wlan0: AP-DISABLED Tue Oct 31 23:59:22 2017 daemon.notice netifd: radio0 (30572): wlan0: Unable to setup interface. Tue Oct 31 23:59:22 2017 daemon.notice netifd: radio0 (30572): wlan0: interface state DISABLED->DISABLED Tue Oct 31 23:59:22 2017 daemon.notice netifd: radio0 (30572): wlan0: AP-DISABLED Tue Oct 31 23:59:22 2017 daemon.notice netifd: radio0 (30572): hostapd_free_hapd_data: Interface wlan0 wasn't started Tue Oct 31 23:59:22 2017 daemon.notice netifd: radio0 (30572): nl80211: deinit ifname=wlan0 disabled_11b_rates=0 Tue Oct 31 23:59:22 2017 daemon.notice netifd: radio0 (30572): cat: can't open '/var/run/wifi-phy0.pid': No such file or directory Tue Oct 31 23:59:22 2017 kern.info kernel: [13821.090000] device wlan1 entered promiscuous mode Tue Oct 31 23:59:22 2017 kern.info kernel: [13821.090000] br-lan: port 2(wlan1) entered forwarding state Tue Oct 31 23:59:22 2017 kern.info kernel: [13821.100000] br-lan: port 2(wlan1) entered forwarding state Tue Oct 31 23:59:22 2017 daemon.notice netifd: radio1 (30592): wlan1: interface state UNINITIALIZED->HT_SCAN Tue Oct 31 23:59:22 2017 daemon.notice netifd: radio0 (30572): Command failed: Invalid argument Tue Oct 31 23:59:22 2017 daemon.notice netifd: radio0 (30572): Device setup failed: HOSTAPD_START_FAILED Tue Oct 31 23:59:23 2017 kern.info kernel: [13821.950000] br-lan: port 2(wlan1) entered disabled state Tue Oct 31 23:59:24 2017 daemon.notice netifd: radio1 (30592): 20/40 MHz operation not permitted on channel pri=11 sec=7 based on overlapping BSSes Tue Oct 31 23:59:24 2017 daemon.notice netifd: radio1 (30592): Using interface wlan1 with hwaddr f0:b4:29:58:bb:f0 and ssid "asdfghjkl" Tue Oct 31 23:59:24 2017 kern.info kernel: [13822.690000] br-lan: port 2(wlan1) entered forwarding state Tue Oct 31 23:59:24 2017 kern.info kernel: [13822.690000] br-lan: port 2(wlan1) entered forwarding state Tue Oct 31 23:59:24 2017 daemon.notice netifd: radio1 (30592): wlan1: interface state HT_SCAN->ENABLED Tue Oct 31 23:59:24 2017 daemon.notice netifd: radio1 (30592): wlan1: AP-ENABLED Tue Oct 31 23:59:24 2017 daemon.notice netifd: Network device 'wlan1' link is up Tue Oct 31 23:59:26 2017 kern.info kernel: [13824.690000] br-lan: port 2(wlan1) entered forwarding state Success
Can you please change to channel 36 and check if your wifi comes online?
I expect the issue is you are selecting a DFS channel
https://lantisproject.com/downloads/gargoylebuilds for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.
Please be respectful when posting. I do this in my free time on a volunteer basis.
Re: Version 1.10.0 : New stable version with critical security fixes
I had tried each available channel for 5ghz, so both 36 and 52 have been used but still nothing. It should be something else.Lantis wrote:kanenas wrote:Lantis wrote:Can you please provide a “dmesg” and “logread” 30 seconds after issuing a “wifi” command at the command line?
...............................
In your screenshot it says you are selecting channel 149. In this log it shows 52.
Can you please change to channel 36 and check if your wifi comes online?
I expect the issue is you are selecting a DFS channel
Re: Version 1.10.0 : New stable version with critical security fixes
Can you please present the same logs when using 36?
I'm just following what the errors say.
Also, what router is this?
I think possibly need to set regulatory region.
I'm just following what the errors say.
Also, what router is this?
I think possibly need to set regulatory region.
https://lantisproject.com/downloads/gargoylebuilds for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.
Please be respectful when posting. I do this in my free time on a volunteer basis.