Are you talking about the v2? Did you ever figure out what was going on? I know historically there's been an issue with this, but I thought 1.9.1 supported it.tapper wrote:flashed my c7 and had no 5 ghz had to go back to last 1.9.x
Version 1.9.1
Moderator: Moderators
Re: Version 1.9.1
Re: Version 1.9.1
Hi mate it was the c7 v2 and it got fixt by a firstboot and reflashing. It now runs sweet as a nut. Just don't save settings if upgrading from 1.9.0
Linksys WRT3200ACM
NETGEAR Nighthawk R7800
NETGEAR R6260
NETGEAR Nighthawk R7800
NETGEAR R6260
Re: Version 1.9.1
Try both but doesn't help. Still back to factory default after power cycle.Lantis wrote:Firstboot reset or reflashing 1.9.1 then try again.
Revert back to 1.6.2 and configurations retain even after power cycle.
Re: Version 1.9.1
4 meg router?ctsffd wrote:Try both but doesn't help. Still back to factory default after power cycle.Lantis wrote:Firstboot reset or reflashing 1.9.1 then try again.
Revert back to 1.6.2 and configurations retain even after power cycle.
Re: Version 1.9.1
Hi Peeps was just going to test out the new FW on my wndr3800 and noticed that there are 2 types? 1 with CH and other with out, whats CH mean?
Re: Version 1.9.1
It's for if you're stuck with the WNDR3800CH running Charter factory firmware.kuss wrote:Hi Peeps was just going to test out the new FW on my wndr3800 and noticed that there are 2 types? 1 with CH and other with out, whats CH mean?
Re: Version 1.9.1
it isFlash ROM 8 MB/RAM 32 MBispyisail wrote:4 meg router?ctsffd wrote:Try both but doesn't help. Still back to factory default after power cycle.Lantis wrote:Firstboot reset or reflashing 1.9.1 then try again.
Revert back to 1.6.2 and configurations retain even after power cycle.
-
- Posts: 41
- Joined: Thu Dec 03, 2015 3:20 am
Re: Version 1.9.1
Just wanted to share my experience with my 1043ND v2.1. I made a backup and updated without preserving settings and that works OK, but the moment I restored my backup, the router would enter a reboot loop. Had to use a failsafe reset to get it going again. It looks like I have to migrate my settings manually
Anyone hazard a guess on why this happens? I'm using quite a few features, mainly DHCP reservation, QOS uplink and downlink rules.
http://i.imgur.com/33mvgIC.png
Seems like I'm gonna have to re-configure my router from scratch... sigh
Anyone hazard a guess on why this happens? I'm using quite a few features, mainly DHCP reservation, QOS uplink and downlink rules.
http://i.imgur.com/33mvgIC.png
Seems like I'm gonna have to re-configure my router from scratch... sigh
Re: Version 1.9.1
You didn't mention which version you came from, but the settings were most likely not compatible.
Preserve settings is EXACTLY THE SAME as making a backup and then restoring it later.
If one was to fail (which there are many reports of this) then the other surely will as well.
You can manually restore certain settings (e.g. DHCP reservations, QOS rules) but not all of them (e.g. Network and wireless settings)
Preserve settings is EXACTLY THE SAME as making a backup and then restoring it later.
If one was to fail (which there are many reports of this) then the other surely will as well.
You can manually restore certain settings (e.g. DHCP reservations, QOS rules) but not all of them (e.g. Network and wireless settings)
https://lantisproject.com/downloads/gargoylebuilds for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.
Please be respectful when posting. I do this in my free time on a volunteer basis.