Page 2 of 6
Re: Version 1.5.3 & 1.4.6
Posted: Fri Feb 03, 2012 2:34 pm
by hnl_dk
hnl_dk wrote:jaykumar2001 wrote:And the latest OpenWrt release is Backfire Interim Release 1 (10.03.1), right?
No, I guess this is backfire SVN revision 29961.
This includes fixes to backfire 10.03.1.
Working fine one my two tl-wr1043nd
Re: Version 1.5.3 & 1.4.6
Posted: Fri Feb 03, 2012 4:21 pm
by sco77
Best build yet, thanks!
Re: Version 1.5.3 & 1.4.6
Posted: Sat Feb 04, 2012 6:34 am
by kris87
Hi!
Can I upgrade directly from v. 1.4.5 to v. 1.5.3 or just to v. 1.4.6? Anyway is it make any sence to use v. 1.5.3 instead of v. 1.4.6 on TP-Link wr-741nd?
Re: Version 1.5.3 & 1.4.6
Posted: Sat Feb 04, 2012 11:22 am
by lilspanyol
Can I update directly from 1.5.0 to 1.5.3?
1043ND V8
Re: Version 1.5.3 & 1.4.6
Posted: Sat Feb 04, 2012 11:56 am
by hnl_dk
lilspanyol wrote:Can I update directly from 1.5.0 to 1.5.3?
1043ND V8
yes and no...
you can update directly, but there is no guarantee that you are able to restore the configuration, if you jump updates.
Re: Version 1.5.3 & 1.4.6
Posted: Sat Feb 04, 2012 1:06 pm
by lceron80
@eric,
thanks for another improved release. there is this small issue that i discovered while verifying bw distribution. see the link below as well... thanks.
http://www.gargoyle-router.com/phpbb/vi ... =12&t=2276
Re: Version 1.5.3 & 1.4.6
Posted: Sat Feb 04, 2012 1:16 pm
by mix
kris87,
You can upgrade to either version. However, because your router has 32 mb of ram, and no usb port to install a flash drive and create swap partition on, you basically will get no added functionality compared to the 1.4.x series. I'd stick with the 1.4.x series personally if I was using your router. But do upgrade, because 1.4.6 (or 1.5.3) has fixes for Atheros wireless devices, and your router uses one.
Re: Version 1.5.3 & 1.4.6
Posted: Sat Feb 04, 2012 9:49 pm
by 2ks-kyle
Hello,
First time here. I just updated from 1.52 to 1.53 on my WNDR3700v2. Its working great! I've been very impressed with Gargoyle. My router had good signal strength before but its even better with Gargoyle. TOR runs well and is easy to use.
Thanks
Re: Version 1.5.3 & 1.4.6
Posted: Sun Feb 05, 2012 4:49 am
by ispyisail
jaykumar2001 wrote:Trying to upgrade my TL WR1043ND with
Code: Select all
gargoyle_1.5.3-ar71xx-tl-wr1043nd-v1-squashfs-sysupgrade.bin
using web interface, its just stuck in uploading firmware. No further action. Router reboots and I am still on firmware 1.5.2, with all my old configuration. (guess nothing happened at all)
What am I doing wrong?
Should I use the following commandline upgrade option?
1) cd /tmp
2) wget
http://www.gargoyle-router.com/download ... pgrade.bin
3) md5sum gargoyle_1.5.3-ar71xx-tl-wr1043nd-v1-squashfs-sysupgrade.bin
4) Make sure the md5sum matches the one listed on the gargoyle download page, which should be ................
5) mtd -r write gargoyle_1.5.3-ar71xx-tl-wr1043nd-v1-squashfs-sysupgrade.bin firmware
I have had very similar problems
My solution was to use failsafe to reset my router to default
Re: Version 1.5.3 & 1.4.6
Posted: Sun Feb 05, 2012 9:31 am
by dreams_idea
Thanks .. my question 1.5.2 version, if the wifi under a large number of packet transmission, the system will be the reboot.Resolved in the 1.5.3 version!Really great!
http://www.gargoyle-router.com/phpbb/vi ... 100#p10632