Versions 1.9.0 & 1.8.1
Moderator: Moderators
Re: Versions 1.9.0 & 1.8.1
Any known 1.8.1 bugs with wr1043ndv2 (currently running stock firmware since I bought it recently)
Re: Versions 1.9.0 & 1.8.1
the problem still exist.emukim wrote:i will continute watching if this kind of problem happen again.
later i will turn to use 1.6.2. since 1.8.0 is not available.
or
can anyone provide me 1.8.0 firmware ?
Re: Versions 1.9.0 & 1.8.1
As previously posted within the 1.8.0 Thread, 1.8.1 on my TL-WR941ND v3.6 Wireless Router is also Truncating DHCP Entries. In this case I discovered the last 8 (out of total of 100) "Ethers" Entries had been Truncated (all of "Hosts" Entries were still intact)! This occurred within 2 Days of the upgrade from 1.6.2 to 1.8.1. Changes since the upgrade: MAC Addresses on 2 existing DHCP Entries had been revised.
I have again returned to 1.6.2...
I have again returned to 1.6.2...
-
- Posts: 28
- Joined: Mon Apr 08, 2013 8:20 am
Re: Versions 1.9.0 & 1.8.1
Except the one I mentioned on the first page, there are no issues at all.ex1t wrote:Any known 1.8.1 bugs with wr1043ndv2 (currently running stock firmware since I bought it recently)
Re: Versions 1.9.0 & 1.8.1
i have found out the issue about happen to my network system.
THE MODEM is not working correctly.
it has critical faults, 5~6 times a day.
Now re-testing version 1.8.1.
Hope it will work fine.
THE MODEM is not working correctly.
it has critical faults, 5~6 times a day.
Now re-testing version 1.8.1.
Hope it will work fine.
Last edited by emukim on Tue Nov 17, 2015 5:46 am, edited 1 time in total.
Re: Versions 1.9.0 & 1.8.1
Can you provide some more detail about the errors when if you see them again pleaseemukim wrote:THE MODERM is not working correctly.
it has critical faults, 5~6 times a day.
Can you help someone else get Gargoyle up and running?
TL-WDR3600 : Gargoyle 1.9.0 : NBN FixedWireless
TL-WR1043ND-V2 : Gargoyle 1.8.0 : 3G Huawei E160E
TL-WDR3600 : Gargoyle 1.9.0 : NBN FixedWireless
TL-WR1043ND-V2 : Gargoyle 1.8.0 : 3G Huawei E160E
Re: Versions 1.9.0 & 1.8.1
Has anyone seen this bug else or was it a single case?gumball3000 wrote:Except the one I mentioned on the first page, there are no issues at all.ex1t wrote:Any known 1.8.1 bugs with wr1043ndv2 (currently running stock firmware since I bought it recently)
And has anyone seen other problems?
I have the TP-Link WR1043ND rev1.8 with firmware 1.8.0 and all is well, but I want to try to improve the signal Wi fi with 1.8.1 firmware which fixed a hardware modes on wireless N routers.
Re: Versions 1.9.0 & 1.8.1
Factory reset works fine for me.
https://lantisproject.com/downloads/gargoylebuilds for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.
Please be respectful when posting. I do this in my free time on a volunteer basis.
Re: Versions 1.9.0 & 1.8.1
Thanks to everybody here for Gargoyle.
I think found a small bug in 1.8.1 and 1.9.0
TL-WDR4300 flash without preserving settings.
Right after setting password and timezone I change WLAN settings:
Wireless Mode: Access Point (AP)
Operation Mode: N+A
Save
It is now working only in 5 GHz as expected and only the 5 GHz LED is on.
But the page does not reflect the settings.
It shows 'Dual Band' and 2.4GHz SSID + 5GHz SSID
If I then change some other settings and save the page again I get 2.4GHz without asking for it.
I think found a small bug in 1.8.1 and 1.9.0
TL-WDR4300 flash without preserving settings.
Right after setting password and timezone I change WLAN settings:
Wireless Mode: Access Point (AP)
Operation Mode: N+A
Save
It is now working only in 5 GHz as expected and only the 5 GHz LED is on.
But the page does not reflect the settings.
It shows 'Dual Band' and 2.4GHz SSID + 5GHz SSID
If I then change some other settings and save the page again I get 2.4GHz without asking for it.
● wrt1200ac (wired-only router)
AP's or for test:
● tl-wdr4300 OpenWrt 18.06.0 (too small for 1.11.X)
● tl-wr841nd OpenWrt 18.06.0 (too small for 1.11.X)
● tew-691gr OpenWrt 18.06.0
AP's or for test:
● tl-wdr4300 OpenWrt 18.06.0 (too small for 1.11.X)
● tl-wr841nd OpenWrt 18.06.0 (too small for 1.11.X)
● tew-691gr OpenWrt 18.06.0
Re: Versions 1.9.0 & 1.8.1
Can confirm.n8b wrote:Thanks to everybody here for Gargoyle.
I think found a small bug in 1.8.1 and 1.9.0
TL-WDR4300 flash without preserving settings.
Right after setting password and timezone I change WLAN settings:
Wireless Mode: Access Point (AP)
Operation Mode: N+A
Save
It is now working only in 5 GHz as expected and only the 5 GHz LED is on.
But the page does not reflect the settings.
It shows 'Dual Band' and 2.4GHz SSID + 5GHz SSID
If I then change some other settings and save the page again I get 2.4GHz without asking for it.
https://lantisproject.com/downloads/gargoylebuilds for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.
Please be respectful when posting. I do this in my free time on a volunteer basis.