Version 1.6.1 - Heartbleed Fix
Moderator: Moderators
Re: Version 1.6.1 - Heartbleed Fix
seems V1.6.1 still not worked with my WHR-G301N, always restore configuration after a power off.
-
- Posts: 28
- Joined: Mon Apr 08, 2013 8:20 am
Re: Version 1.6.1 - Heartbleed Fix
[BUG REPORT]
After i choose Restore Default Configuration the router doesn't reboot by itself, and if i try to access the default link, i receive the following message:
After i choose Restore Default Configuration the router doesn't reboot by itself, and if i try to access the default link, i receive the following message:
I had to reboot the rooter via SSH.haserl CGI Error
The fallback language was not set for gargoyle.global.fallback_lang
Re: Version 1.6.1 - Heartbleed Fix
Bug confirmed on my 1043nd v1.gumball3000 wrote:[BUG REPORT]
After i choose Restore Default Configuration the router doesn't reboot by itself, and if i try to access the default link, i receive the following message:I had to reboot the rooter via SSH.haserl CGI Error
The fallback language was not set for gargoyle.global.fallback_lang
To me, the only solution was to put router in failsafe mode and digit "firstboot" command from telnet session. After that just run "reboot -p" command and config again the router.
Re: Version 1.6.1 - Heartbleed Fix
found a bug wen i turn on tor it looks like it is on but wen you go back to the page it is switched off again. and tor sites will not load.
Linksys WRT3200ACM
NETGEAR Nighthawk R7800
NETGEAR R6260
NETGEAR Nighthawk R7800
NETGEAR R6260
-
- Posts: 1
- Joined: Tue Apr 22, 2014 2:35 pm
Re: Version 1.6.1 - Heartbleed Fix
Applied 1.6.1 to my TP-Link TL-WDR3600 v1. Update applied OK but TOR is now shown as not installed, and will not install.
If I hit "Install" on the Tor Plugin I get the "please wait" pop-up, then the screen refreshes but TOR is still shown as "Status: Not Installed".
Installed the system log plugin and tried to install TOR, nothing recorded.
Rebooted the router and tried to install TOR, still not installed.
restored from the backup I took before upgrading, retried installing TOR, still not installed. Power-cycled the router, retired install, TOR still not installed.
Anyone have any hints as to where to look next?
If I hit "Install" on the Tor Plugin I get the "please wait" pop-up, then the screen refreshes but TOR is still shown as "Status: Not Installed".
Installed the system log plugin and tried to install TOR, nothing recorded.
Rebooted the router and tried to install TOR, still not installed.
restored from the backup I took before upgrading, retried installing TOR, still not installed. Power-cycled the router, retired install, TOR still not installed.
Anyone have any hints as to where to look next?
Re: Version 1.6.1 - Heartbleed Fix
gumball3000/tt99 : You are trying to restore a configuration from a much earlier version of Gargoyle, before internationalization support was added. This is not supported
tapper: I'm having trouble reproducing this error. Please clarify what router you are using, what version of Gargoyle you upgraded from, and how you have Tor configured (as a client only, or as a relay? Hidden Service only/Everything goes through tor/Selected by each host? ) The more information I have the more likely it is that I can figure out what might be going on.
eponymous cowherd: The WDR3600 only has 8MB of flash. I'm guessing you upgraded from 1.5.10 or before? Tor was removed from routers with less than 16MB of flash in 1.5.11, and needs to be installed as a separate plugin. In order to make Tor fit, you need to have a USB drive, and install the Tor plugin to that drive in the System/Plugins page.
tapper: I'm having trouble reproducing this error. Please clarify what router you are using, what version of Gargoyle you upgraded from, and how you have Tor configured (as a client only, or as a relay? Hidden Service only/Everything goes through tor/Selected by each host? ) The more information I have the more likely it is that I can figure out what might be going on.
eponymous cowherd: The WDR3600 only has 8MB of flash. I'm guessing you upgraded from 1.5.10 or before? Tor was removed from routers with less than 16MB of flash in 1.5.11, and needs to be installed as a separate plugin. In order to make Tor fit, you need to have a USB drive, and install the Tor plugin to that drive in the System/Plugins page.
Re: Version 1.6.1 - Heartbleed Fix
Hi Eric i am using 1.6.1 on a TP-Link WR1043ND
v2.1 with 128 swop file on a 256 meg USB stick.
plugin root /dev/sda1: 121.246 MBytes Total, 119.412 MBytes Free
Plugin Sources:
table with 2 columns and 3 rows
Name
attitude_adjustment
http://downloads.openwrt.org/attitude_a ... c/packages
Preset
gargoyle
http://www.gargoyle-router.com/packages ... xx/default
Preset
table end
Tor Anonymizer Support for Gargoyle
Version: 1.6.1-1
Status: Installed
Uninstall
So i set it to
Hidden Service Access Only
and then hit save
Tor Data Drive:
/dev/sda1: 121.246 MBytes Total, 119.412 MBytes Free
then hit save.
Wtf it's started working now lol
v2.1 with 128 swop file on a 256 meg USB stick.
plugin root /dev/sda1: 121.246 MBytes Total, 119.412 MBytes Free
Plugin Sources:
table with 2 columns and 3 rows
Name
attitude_adjustment
http://downloads.openwrt.org/attitude_a ... c/packages
Preset
gargoyle
http://www.gargoyle-router.com/packages ... xx/default
Preset
table end
Tor Anonymizer Support for Gargoyle
Version: 1.6.1-1
Status: Installed
Uninstall
So i set it to
Hidden Service Access Only
and then hit save
Tor Data Drive:
/dev/sda1: 121.246 MBytes Total, 119.412 MBytes Free
then hit save.
Wtf it's started working now lol
Linksys WRT3200ACM
NETGEAR Nighthawk R7800
NETGEAR R6260
NETGEAR Nighthawk R7800
NETGEAR R6260
Re: Version 1.6.1 - Heartbleed Fix
No it's not working
URL/grams7enufi7jmdl.onion)
URL/grams7enufi7jmdl.onion)
Linksys WRT3200ACM
NETGEAR Nighthawk R7800
NETGEAR R6260
NETGEAR Nighthawk R7800
NETGEAR R6260
-
- Posts: 28
- Joined: Mon Apr 08, 2013 8:20 am
Re: Version 1.6.1 - Heartbleed Fix
@Eric I triple checked, first i updated 1.6.0 to 1.6.1, the box "Attempt to Preserve Settings" was checked, and i received that error, after that i rebooted the router (via SSH) and i choose "Restore Default Configuration"
and I got the same error.
After that i reflashed the same firmware and I had unchecked the box "Attempt to Preserve Settings" the router still didn't rebooted by itself and i saw the same error, after that i rebooted it via SSH.
Gargoyle interface language was set to english all the time.
So, I'm pretty sure this is a bug.
1043nd v1.8
and I got the same error.
After that i reflashed the same firmware and I had unchecked the box "Attempt to Preserve Settings" the router still didn't rebooted by itself and i saw the same error, after that i rebooted it via SSH.
Gargoyle interface language was set to english all the time.
So, I'm pretty sure this is a bug.
1043nd v1.8
Re: Version 1.6.1 - Heartbleed Fix
About TOR plug-in version
I think OpenWRT TOR version is 0.2.4.21
and Gargoyle version for it is 1.6.1-1
Right ?
I think OpenWRT TOR version is 0.2.4.21
and Gargoyle version for it is 1.6.1-1
Right ?