I have recently purchased a WR1043ND router and have been reading through the website and the forums. I think all I've managed to do is confuse myself (admittedly not a very difficult task). The download section of the website states that I should load V1.3.14 experimental, but I've read on the forum that others are using V1.5.8 with no issues. Should I go straight to V1.5.8 or do I have to load V1.3.14 first then upgrade? Then there's the whole OpenWrt, Kamakazie, packages, images - which should I use ??? Help please
I could really use a 'step-by-step' set of instructions on how to get Gargolye loaded and running on the new router.
Newbie needs TL-WR1043ND setup help
Moderator: Moderators
Re: Newbie needs TL-WR1043ND setup help
Since you are upgrading from the factory firmware use
gargoyle_1.5.9-ar71xx-generic-tl-wr1043nd-v1-squashfs-factory.bin
Which can be found in the download section (Atheros AR71XX) of this website.
Step1> Download file
Step2> Perform firmware upgrade using the file you downloaded and the appropriate pick on your routers web page.
Step3> Have a cup of coffee while the software updates.
Step4> Login into Gargoyle, experiment, search the forum, post if you cannot find what you need.
gargoyle_1.5.9-ar71xx-generic-tl-wr1043nd-v1-squashfs-factory.bin
Which can be found in the download section (Atheros AR71XX) of this website.
Step1> Download file
Step2> Perform firmware upgrade using the file you downloaded and the appropriate pick on your routers web page.
Step3> Have a cup of coffee while the software updates.
Step4> Login into Gargoyle, experiment, search the forum, post if you cannot find what you need.
Linksys WRT1900ACv2
Netgear WNDR3700v2
TP Link 1043ND v3
TP-Link TL-WDR3600 v1
Buffalo WZR-HP-G300NH2
WRT54G-TM
Netgear WNDR3700v2
TP Link 1043ND v3
TP-Link TL-WDR3600 v1
Buffalo WZR-HP-G300NH2
WRT54G-TM
Re: Newbie needs TL-WR1043ND setup help
One more thing I found recently, sometimes you need to rename the gargoyle file to something simpler filename wise e.g. Image.bin in order for the standard TP-link firmware to be able to use the file.
Good luck, 1.5.9 worked fine on my 1043nd.
Rob
Good luck, 1.5.9 worked fine on my 1043nd.
Rob
-
- Posts: 10
- Joined: Fri Feb 01, 2013 1:02 pm
Re: Newbie needs TL-WR1043ND setup help
pbix wrote:Since you are upgrading from the factory firmware use
gargoyle_1.5.9-ar71xx-generic-tl-wr1043nd-v1-squashfs-factory.bin
Which can be found in the download section (Atheros AR71XX) of this website.
Step1> Download file
Step2> Perform firmware upgrade using the file you downloaded and the appropriate pick on your routers web page.
Step3> Have a cup of coffee while the software updates.
Step4> Login into Gargoyle, experiment, search the forum, post if you cannot find what you need.
Thanks - seems simple enough
Re: Newbie needs TL-WR1043ND setup help
I strongly recommend not to use 1.5.9 with 1043nd
I have too many problems to discuss in a single post.
I suggest 1.5.6
I have too many problems to discuss in a single post.
I suggest 1.5.6
Re: Newbie needs TL-WR1043ND setup help
1.5.6 is not an option on the v1.10 1043ND hardware. It will brick it:grim wrote:I strongly recommend not to use 1.5.9 with 1043nd
I have too many problems to discuss in a single post.
I suggest 1.5.6
http://wiki.openwrt.org/toh/tp-link/tl- ... d.versions
http://www.gargoyle-router.com/phpbb/vi ... f=8&t=3842