EJM3 wrote:===================================================================
I have a couple of GL.iNet 6416A routers that I use as repeaters for my home net, I already have 1.7.1 installed on them. I'd be willing to slap a copy of 1.9.x onto one & give it a test drive, I'd even be sure to run most traffic through the new install to give it a workout; plus report any bugs back to you...
Thanks in advance
Router Model: GLI GL.iNet 6416A
Link to Openwrt wiki: https://wiki.openwrt.org/toh/gl-inet/gl-inet_64xx
Is it supported in Openwrt? Yes
Does it have >= 4MB of flash? Yes
Does it have >= 8MB of flash? Yes
Does it have USB support? Yes
Notes from Lantis: Accepted
EJM3 has reported this firmware as stable.
You can find it here
https://lantisproject.com/downloads/gargoylebuilds for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.
Router Model: D-Link Dir-850L ac1200
Link to Openwrt wiki: ------------
Is it supported in Openwrt? I don't know
Does it have > 4MB of flash? Yes
Does it have > 8MB of flash? Yes
Does it have USB support? Yes
I need a help with my router, i wanna put a gargoyle firmware, but i don't know what is compatible. Can you help me?
Thanks
It isn't supported in Openwrt as far as I can tell.
Your first port of call would be to those guys.
If you go to the wikidevi site you can see that there has been some success with getting openwrt to run on similar chipsets so it may be possible in the future at some stage.
Until then however there is nothing I can do sorry.
https://lantisproject.com/downloads/gargoylebuilds for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.
Router Model: Linksys/Cisco WRT320N
Link to Openwrt wiki: https://wiki.openwrt.org/toh/linksys/wrt320n
Is it supported in Openwrt Chaos_Calmer Branch? Yes
Does it have >= 8MB of flash? Yes
Does it have USB support? No
Router is broadcom BCM4717A1 with 8MB flash.
Almost identical to E2000, except for flash partition layout and bootloader.
The 841n v11 is only supported in the latest trunk builds. If support is back ported to chaos calmer or gargoyle is moves forward you can request again and I'll reevaluate
Cheers .
https://lantisproject.com/downloads/gargoylebuilds for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.
Router Model: Ubiquiti EdgeRouter Lite
Link to Openwrt wiki: https://wiki.openwrt.org/toh/ubiquiti/edgerouter.lite
Is it supported in Openwrt Chaos_Calmer Branch? Yes
Does it have >= 8MB of flash? Yes
Does it have USB support? Yes
I would appreciate if you look into making this firmware available for
Router Model: TP Link TL WR1043 v3.0
Link to Openwrt wiki: https://wiki.openwrt.org/toh/hwdata/tp- ... r1043nd_v3
Is it supported in Openwrt? Yes
Does it have >= 4MB of flash? Yes
Does it have >= 8MB of flash? Yes
Does it have USB support? Yes
Hi guys, is it possible to support this router too?
Thank you.
Router Model: Meraki MR12
Link to Openwrt wiki: https://wiki.openwrt.org/toh/meraki/mr12
Is it supported in Openwrt? Yes , since r45726 (CC trunk)
Does it have >= 4MB of flash? Yes 16MB
Does it have >= 8MB of flash? Yes 16MB
Does it have USB support? No
TP Link TL WR1043 v3.0
+1 for above request! Would be much appreciated. This chassis is a great work horse with a good radio section - I install a few every week!
Apparently it's the same hardware as v2, just needs the "h/w identifier" code changed.
Router Model: TP Link TL WR1043 v3.0
Link to Openwrt wiki: https://wiki.openwrt.org/toh/hwdata/tp- ... r1043nd_v3
Is it supported in Openwrt? Yes
Does it have >= 4MB of flash? Yes
Does it have >= 8MB of flash? Yes
Does it have USB support? Yes