I assume you're right ...ispyisail wrote:I suspect the problem its at the openwrt level?
Search found 20 matches
- Thu Sep 08, 2011 11:06 am
- Forum: General Discussion
- Topic: D-Link DIR-300 settings lost after reboot
- Replies: 4
- Views: 3868
Re: D-Link DIR-300 settings lost after reboot
- Thu Sep 08, 2011 4:51 am
- Forum: General Discussion
- Topic: D-Link DIR-300 settings lost after reboot
- Replies: 4
- Views: 3868
Re: D-Link DIR-300 settings lost after reboot
if it's a known problem will it be fixed in the future ?
- Tue Sep 06, 2011 8:54 am
- Forum: General Discussion
- Topic: D-Link DIR-300 settings lost after reboot
- Replies: 4
- Views: 3868
D-Link DIR-300 settings lost after reboot
recently I flashed a DIR-300 with the latest Gargoyle 1.41 now I have the problem that all settings are lost after a reboot already tried a full factory reset but problem persists - for example if I enable WIFI and hit apply WIFI is on - after reboot it is off again also the password I setup is gone...
- Tue Sep 06, 2011 5:14 am
- Forum: General Discussion
- Topic: disable bandwidth monitoring permanently
- Replies: 3
- Views: 6248
disable bandwidth monitoring permanently
how can I disable the bandwidth monitoring completly ?
I tried:
and BW monitoring is off
but after reboot it is running again
I tried:
Code: Select all
/etc/init.d/bwmon_gargoyle stop
/etc/init.d/bwmon_gargoyle disable
but after reboot it is running again
- Fri Jul 08, 2011 11:12 am
- Forum: News
- Topic: Version 1.3.16 -- Second Release Candidate
- Replies: 69
- Views: 101710
Re: Version 1.3.16 -- Second Release Candidate
Idle timeout problem/question: I am using latest (same problem with previous versions) Gargoyle on a F*nera (FON2100A) in client bridge mode. After a while when nothing is send or received from or to client behind, the F*nera drops connection and I cannot reach Webif anymore. when I run a permanent...
- Thu Jul 07, 2011 8:17 am
- Forum: News
- Topic: Version 1.3.16 -- Second Release Candidate
- Replies: 69
- Views: 101710
Re: Version 1.3.16 -- Second Release Candidate
has nobody an advice for my question/problem ?
- Tue Jul 05, 2011 8:54 am
- Forum: News
- Topic: Version 1.3.16 -- Second Release Candidate
- Replies: 69
- Views: 101710
Re: Version 1.3.16 -- Second Release Candidate
Idle timeout problem/question: I am using latest (same problem with previous versions) Gargoyle on a F*nera (FON2100A) in client bridge mode. After a while when nothing is send or received from or to client behind, the F*nera drops connection and I cannot reach Webif anymore. when I run a permanent ...
- Fri Feb 12, 2010 10:25 am
- Forum: Other Issues
- Topic: Fonera 2201 client bridge problem
- Replies: 5
- Views: 4172
Re: Fonera 2201 client bridge problem
these are the last outputs in serial console before ping stops during boot:
AP mode is working fine btw...
Code: Select all
device ath0 entered promiscuous mode
br-lan: port 3(ath0) entering learning state
br-lan: topology change detected, propagating
br-lan: port 3(ath0) entering forwarding state
- Thu Feb 11, 2010 11:32 am
- Forum: Other Issues
- Topic: Fonera 2201 client bridge problem
- Replies: 5
- Views: 4172
Re: Fonera 2201 client bridge problem
Any special settings you used? afaik no I usually use WPA2-AES or WEP 128-bit - depending on which AP I'm connecting to, to do the testing. I would like to use WPA2-AES too reason why I want to assign the WAN port to the switch: I would like to bridge my XBOX and DBOX to my WLAN and therefore I nee...
- Thu Feb 11, 2010 5:21 am
- Forum: Other Issues
- Topic: Fonera 2201 client bridge problem
- Replies: 5
- Views: 4172
Fonera 2201 client bridge problem
here is my config.. Device Configuration: - Wireless Bridge/Repeater - WAN Port Bride to LAN - Connect Via Client Bridge - Repeater Disabled and here is the problem.. :D as soon as I switch to bridge the fonera is no longer reachable over IP now the strange thing (for me): I have connected a serial ...