Search found 6777 matches
- Sun May 26, 2024 5:55 am
- Forum: Feature Requests
- Topic: Connected hostnames in DHCP mode
- Replies: 8
- Views: 336
Re: Connected hostnames in DHCP mode
We already have a beta available for flint
- Sun May 26, 2024 5:06 am
- Forum: Hardware / Installation Issues
- Topic: LinksysWRT1900acs v2 bricked !?
- Replies: 13
- Views: 510
Re: LinksysWRT1900acs v2 bricked !?
I think it is unlikely your bootloader is dead.
- Sat May 25, 2024 6:42 pm
- Forum: Hardware / Installation Issues
- Topic: LinksysWRT1900acs v2 bricked !?
- Replies: 13
- Views: 510
Re: LinksysWRT1900acs v2 bricked !?
The jumper that goes between TX and RX allows you to loop back and test. So if your settings are correct you should see what you type out echoed to you. When you are ready to connect to the device you don’t use that jumper only the one that selects voltage. Sorry it’s a bit difficult to assist with ...
- Sat May 25, 2024 8:51 am
- Forum: Hardware / Installation Issues
- Topic: LinksysWRT1900acs v2 bricked !?
- Replies: 13
- Views: 510
Re: LinksysWRT1900acs v2 bricked !?
Perhaps you don't have the right drivers?
https://learn.sparkfun.com/tutorials/ho ... rivers/all
https://learn.sparkfun.com/tutorials/ho ... rivers/all
- Sat May 25, 2024 7:24 am
- Forum: General Discussion
- Topic: IPV6 over RNDIS
- Replies: 5
- Views: 203
Re: IPV6 over RNDIS
Yes I didn't spot eth0.1, that should go as well.
I'm not sure (I can't find any documentation) if Telstra mobile internet does prefix delegation.
I'm not sure (I can't find any documentation) if Telstra mobile internet does prefix delegation.
- Fri May 24, 2024 9:03 am
- Forum: General Discussion
- Topic: IPV6 over RNDIS
- Replies: 5
- Views: 203
Re: IPV6 over RNDIS
Did you keep settings moving to this version? You've got some ugly stuff going on with both ifname and device defined for wan and wan6. Try deleting ifname from both wan and wan6 and see if that fixes it. ifname is old syntax but it is still supported, and there might be a race condition between the...
- Thu May 23, 2024 9:30 am
- Forum: Feature Requests
- Topic: Connected hostnames in DHCP mode
- Replies: 8
- Views: 336
Re: Connected hostnames in DHCP mode
Edit /etc/config/dhcp and add a static host entry. You only need to include the name and the IP or MAC that identifies it. Neither of these work with the GUI as we require both IP and MAC, not one or the other. In current versions of Gargoyle only the IP entries will work for what you want to do. It...
- Thu May 23, 2024 6:11 am
- Forum: General Discussion
- Topic: IPV6 over RNDIS
- Replies: 5
- Views: 203
Re: IPV6 over RNDIS
No reason it shouldn’t.
Are you running something newer than 1.12 yet?
If so, please post your /etc/config/network
Are you running something newer than 1.12 yet?
If so, please post your /etc/config/network
- Mon May 20, 2024 6:26 pm
- Forum: Hardware / Installation Issues
- Topic: LinksysWRT1900acs v2 bricked !?
- Replies: 13
- Views: 510
Re: LinksysWRT1900acs v2 bricked !?
It must be 3.3v tx rx. You are correct to not connect power.
Read the wiki, it tells you that they are a 2mm pitch pin. Most cables you can buy are 2.54mm so you will have difficulty attaching the pins. If you can find 2mm is best otherwise you might need to cut/shave to fit.
Read the wiki, it tells you that they are a 2mm pitch pin. Most cables you can buy are 2.54mm so you will have difficulty attaching the pins. If you can find 2mm is best otherwise you might need to cut/shave to fit.
- Mon May 20, 2024 8:14 am
- Forum: Feature Requests
- Topic: Connected hostnames in DHCP mode
- Replies: 8
- Views: 336
Re: Connected hostnames in DHCP mode
How do you want to identify the hosts? Are their IP's stable or do you need to identify them by MAC?